Pololu 3.3V, 500mA Step-Down Voltage Regulator D24V5F3
Pololu 3.3V, 500mA Step-Down Voltage Regulator D24V5F3
Share
The D24V5Fx family of buck (step-down) voltage regulators generates lower output voltages from input voltages as high as 36 V. They are switching regulators (also called switched-mode power supplies (SMPS) or DC-to-DC converters) and have a typical efficiency between 80% to 93%, which is much more efficient than linear voltage regulators, especially when the difference between the input and output voltage is large. These regulators have a power-save mode that activates at light loads and a low quiescent (no load) current draw, which make them well suited for low-power applications that are run from a battery. These regulators are available in eight different fixed output voltages:
Top of Form
Select options: (any output voltage)1.8 V2.5 V3.3 V5 V6 V9 V12 V15 V Go ?
Bottom of Form
The different versions of this regulator all look very similar, so the bottom silkscreen includes a blank space where you can add your own distinguishing marks or labels. This product page applies to all eight versions of the D24V5Fx family.
The regulators feature short-circuit/over-current protection, and thermal shutdown helps prevent damage from overheating. The boards do not have reverse-voltage protection.
If you need more output current, consider the very similar D24V10Fx family of step-down voltage regulators, which can deliver up to 1 A in several different output voltages:
Top of Form
Select options: (any output voltage)3.3 V5 V6 V9 V12 V Go ?
Bottom of Form
The picture on the right shows a 1 A D24V10Fx regulator next to a 0.5 A D24V5Fx regulator and a common 7805 linear regulator in a TO-220 package.
Features
· Input voltage:
o 3 V to 36 V for output voltages of 1.8 V and 2.5 V
o [output voltage + dropout voltage] to 36 V for output voltages of 3.3 V and higher (see below for more information on dropout voltage)
· Fixed 1.8 V, 2.5 V, 3.3 V, 5 V, 6 V, 9 V, 12 V, or 15 V output (depending on regulator version) with 4% accuracy
· Maximum output current: 500 mA
· Typical efficiency of 80% to 93%
· 500 kHz switching frequency (when not in power-save mode)
· 200 μA typical no-load quiescent current
· Integrated over-temperature and over-current shutoff
· Small size: 0.5″ × 0.4″ × 0.1″ (13 mm × 10 mm × 3 mm)
The buck regulator has four connections: shutdown (SHDN), input voltage (VIN), ground (GND), and output voltage (VOUT).ConnectionsUsing the regulator
The SHDN pin can be driven low (under 0.4 V) to turn off the output and put the board into a low-power state. There is a 100 kΩ pull-up resistor between the SHDN pin and VIN, so if you want to leave the board permanently enabled, the SHDN pin can be left disconnected. While the SHDNpin is being driven low, the current draw of the regulator is dominated by the current through the pull-up resistor and will be proportional to the input voltage. (At 36 V in it will draw about 360 μA.)
The input voltage, VIN, powers the regulator. Voltages between 3 V and 36 V can be applied to VIN, but for versions of the regulator that have an output voltage higher than 3 V, the effective lower limit of VIN is VOUT plus the regulator’s dropout voltage, which varies approximately linearly with the load (see below for graphs of dropout voltages as a function of the load). Additionally, please be wary of destructive LC spikes (see below for more information).
The output voltage, VOUT, is fixed and depends on the regulator version: the D24V5F1 version outputs 1.5 V, D24V5F2 version outputs 2.5 V, the D24V5F3 version outputs 3.3 V, the D24V5F5 version outputs 5 V, the D24V5F6 version outputs 6 V, the D24V5F9 version outputs 9 V, the D24V5F12 version outputs 12 V, and the D24V5F15 version outputs 15 V
The four connections are labeled on the back side of the PCB and are arranged with a 0.1″ spacing along the edge of the board for compatibility with solderless breadboards, connectors, and other prototyping arrangements that use a 0.1″ grid. You can solder wires directly to the board or solder in either the 4×1 straight male header strip or the 4×1 right-angle male header strip that is included.
The efficiency of a voltage regulator, defined as (Power out)/(Power in), is an important measure of its performance, especially when battery life or heat are concerns. This family of switching regulators typically has an efficiency of 80% to 95%, though the actual efficiency in a given system depends on input voltage, output voltage, and output current. See the efficiency graph near the bottom of this page for more information.Typical efficiency and output current
In order to achieve a high efficiency at low loads, this regulator automatically goes into a power-save mode where the switching frequency is reduced. In power-save mode, the switching frequency of the regulator changes as necessary to minimize power loss. This could make it harder to filter out noise on the output caused by switching.
Typical dropout voltage
The dropout voltage of a step-down regulator is the minimum amount by which the input voltage must exceed the regulator’s target output voltage in order to ensure the target output can be achieved. For example, if a 5 V regulator has a 1 V dropout voltage, the input must be at least 6 V to ensure the output is the full 5 V. Generally speaking, the dropout voltage increases as the output current increases. See the “Details” section below for more information on the dropout voltage for this specific regulator version.
Details for item #2842
The graphs below show the typical efficiency and dropout voltage of the 3.3 V D24V5F3 regulator as a function of the output current:
When connecting voltage to electronic circuits, the initial rush of current can cause voltage spikes that are much higher than the input voltage. If these spikes exceed the regulator’s maximum voltage (36 V), the regulator can be destroyed. In our tests with typical power leads (~30″ test clips), input voltages above 20 V caused spikes over 36 V.LC voltage spikes
If you are connecting more than 20 V or your power leads or supply has high inductance, we recommend soldering a 33 μF or larger electrolytic capacitor close to the regulator between VIN and GND. The capacitor should be rated for at least 50 V.
Featured collection
-
Crazyflie 2.1+
Vendor:Regular price Rs. 26,499.00Regular priceUnit price / per -
Getting Started Bundle
Vendor:Regular price Rs. 26,399.00Regular priceUnit price / per -
Happy hacker bundle
Vendor:Regular price Rs. 33,599.00Regular priceUnit price / per -
STEM ranging bundle
Vendor:Regular price Rs. 43,999.00Regular priceUnit price / per -
Crazyradio 2.0
Vendor:Regular price Rs. 4,399.00Regular priceUnit price / per -
Lighthouse explorer bundle
Vendor:Regular price Rs. 89,999.00Regular priceUnit price / per -
Lighthouse positioning deck
Vendor:Regular price Rs. 9,899.00Regular priceUnit price / per -
Lighthouse V2 base station
Vendor:Regular price Rs. 30,349.00Regular priceUnit price / per -
Lighthouse swarm bundle
Vendor:Regular price Rs. 425,899.00Regular priceUnit price / per -
Loco explorer bundle
Vendor:Regular price Rs. 187,999.00Regular priceUnit price / per -
Loco positioning deck
Vendor:Regular price Rs. 9,899.00Regular priceUnit price / per -
Loco positioning node
Vendor:Regular price Rs. 18,699.00Regular priceUnit price / per -
Loco Swarm Bundle
Vendor:Regular price Rs. 529,609.00Regular priceUnit price / per -
Active marker deck
Vendor:Regular price Rs. 16,499.00Regular priceUnit price / per -
Motion capture marker deck
Vendor:Regular price Rs. 659.00Regular priceUnit price / per -
AI-Deck 1.1
Vendor:Regular price Rs. 27,999.00Regular priceUnit price / per -
AI-Deck Color Camera Module
Vendor:Regular price Rs. 2,199.00Regular priceUnit price / per -
AI-deck monocrome camera module
Vendor:Regular price Rs. 2,199.00Regular priceUnit price / per -
Flow deck v2
Vendor:Regular price Rs. 5,499.00Regular priceUnit price / per -
Crazyflie Bolt
Vendor:Regular price Rs. 21,999.00Regular priceUnit price / per -
Thrust upgrade bundle for Crazyflie 2.X
Vendor:Regular price Rs. 1,949.00Regular priceUnit price / perSold out -
Qi 1.2 wireless charging deck
Vendor:Regular price Rs. 3,849.00Regular priceUnit price / per -
7 mm DC-motor
Vendor:Regular price Rs. 439.00Regular priceUnit price / per -
Male long deck connector
Vendor:Regular price Rs. 219.00Regular priceUnit price / per -
250mAh LiPo battery
Vendor:Regular price Rs. 659.00Regular priceUnit price / per