Pololu Jrk 21v3 USB Motor Controller with Feedback
Pololu Jrk 21v3 USB Motor Controller with Feedback
Share
This product has been replaced by the newer version of Pololu #3142
Description
The jrk 21v3 motor controller is a highly configurable brushed DC motor controller that supports four interface modes: USB, logic-level serial, analog voltage, and hobby radio control (RC). The controller can be used with feedback for closed-loop speed or position control, or it can be used without feedback as an open-loop speed control. The continuous output current is approximately 3 A in the recommended operating range of 8–28 V, with derated performance down to 5 V and transient protection to 40 V. The version ships with connectors included but not soldered in, allowing for custom installations.
Overview
The jrk 21v3 is a versatile, general-purpose motor controller that supports a variety of interfaces, including USB. The broad operating range from 5 V to 28 V and continuous output current of 3 A (5 A peak) allow this board to control most small DC brushed motors. Analog voltage and tachometer (frequency) feedback options allow quick implementation of closed-loop servo systems, and a free configuration utility (for Windows) allows easy calibration and configuration through the USB port.
Key improvements over competing products and earlier Pololu motor controllers with feedback include:
- USB connectivity with emulated serial (COM) port allows direct motor control from a PC.
- Ultrasonic PWM to eliminate switching-induced motor shaft hum or whine.
- Robust, high-speed communication protocol with user-configurable error condition response.
- High internal resolution (12 bits) for smooth and flexible calibration to various input and feedback devices.
- Current sensing and limiting.
- Reversed power protection.
- Field-upgradeable firmware.
Note: A USB A to mini-B cable (not included) is required to connect this controller to a computer.
Main Features of the Jrk 21v3
Two closed-loop feedback options:Simple bidirectional control of one DC brush motor.
- 5 V to 28 V operating supply range.
- 3 A maximum continuous current output (5 A peak).
- Four communication or control options:
- USB interface for direct connection to a PC.
- Full-duplex, TTL-level asynchronous serial interface for direct connection to microcontrollers or other embedded controllers.
- Hobby radio control (RC) pulse width interface for direct connection to an RC receiver or RC servo controller.
- 0–5 V analog voltage interface for direct connection to potentiometers and analog joysticks.
- 0–5 V analog voltage.
- Frequency/tachometer digital input up to 2 MHz with 1 ms PID period.
(Open-loop control with no feedback also available.)
- Simple configuration and calibration over USB with free configuration program (Windows 8, Windows 7, Vista, and Windows XP compatible).
- Configurable parameters include:
- PID period and PID constants (feedback tuning parameters).
- Maximum current.
- Maximum duty cycle.
- Maximum acceleration.
- Error response.
- Input calibration (learning) for analog and RC control.
- Optional CRC error detection eliminates communication errors caused by noise or software faults.
- Reversed power protection.
- Field-upgradeable firmware.
- Optional feedback potentiometer disconnect detection.
- Comprehensive user’s guide.
Specifications
Motor channels: |
1 |
Operating voltage: |
5 – 28 V |
Continuous output current: |
3 A |
Peak output current: |
5 A |
Auto-detect baud rate range: |
300 – 115,200 bps |
Available fixed baud rates: |
300 – 115,200 bps |
Available PWM frequencies: |
20 kHz, 5 kHz |
Reverse voltage protection?: |
Yes |
USB connector style: |
USB Mini-B |
The jrk 21v3 is the smaller of two jrk motor controllers. For a higher-power version, see the jrk 12v12
Included Hardware
|
|
The jrk 21v3 is available in two versions: “fully assembled” with terminal blocks and 0.1″ male header pins pre-installed (left picture above), and connector-free (right picture above). The connector-free version includes a straight 0.1″ breakaway male header strip and two 3.5mm, 2-pin terminal blocks, but these parts are not soldered to the board, which allows for custom installations.
The three mounting holes are intended for use with #2 screws (not included).
Example Feedback System – 4 Methods of Control
|
|
||||
|
|
Dimensions
Size: | 1.35" x 1.35" x 0.4"1 |
---|
General specifications
Motor driver: | MC33926 |
---|---|
Motor channels: | 1 |
Control interface: | USB; non-inverted TTL serial; RC servo pulses; analog voltage2 |
Minimum operating voltage: | 5 V |
Maximum operating voltage: | 28 V |
Continuous output current per channel: | 3 A |
Peak output current per channel: | 5 A |
Current sense: | 0.5 V/A3 |
Maximum PWM frequency: | 20 kHz |
Minimum logic voltage: | 4 V4 |
Maximum logic voltage: | 5 V |
Reverse voltage protection?: | Y |
Partial kit?: | Y |
Version: | original 21v3 (28 V max, 3 A max continuous) |
Notes:
1. Without included hardware.
2. Autodetects baud rates between 300 and 115,200 bps, or can be set to any fixed baud rate in this range.
3. Current readings are converted to a digital number from 0-255.
3. In RC mode, the pulses can be as low as 2V.
Featured collection
-
Crazyflie 2.1+
Vendor:Regular price Rs. 26,499.00Regular priceUnit price / per -
Getting Started Bundle
Vendor:Regular price Rs. 26,399.00Regular priceUnit price / per -
Happy hacker bundle
Vendor:Regular price Rs. 33,599.00Regular priceUnit price / per -
STEM ranging bundle
Vendor:Regular price Rs. 43,999.00Regular priceUnit price / per -
Crazyradio 2.0
Vendor:Regular price Rs. 4,399.00Regular priceUnit price / per -
Lighthouse explorer bundle
Vendor:Regular price Rs. 89,999.00Regular priceUnit price / per -
Lighthouse positioning deck
Vendor:Regular price Rs. 9,899.00Regular priceUnit price / per -
Lighthouse V2 base station
Vendor:Regular price Rs. 30,349.00Regular priceUnit price / per -
Lighthouse swarm bundle
Vendor:Regular price Rs. 425,899.00Regular priceUnit price / per -
Loco explorer bundle
Vendor:Regular price Rs. 187,999.00Regular priceUnit price / per -
Loco positioning deck
Vendor:Regular price Rs. 9,899.00Regular priceUnit price / per -
Loco positioning node
Vendor:Regular price Rs. 18,699.00Regular priceUnit price / per -
Loco Swarm Bundle
Vendor:Regular price Rs. 529,609.00Regular priceUnit price / per -
Active marker deck
Vendor:Regular price Rs. 16,499.00Regular priceUnit price / per -
Motion capture marker deck
Vendor:Regular price Rs. 659.00Regular priceUnit price / per -
AI-Deck 1.1
Vendor:Regular price Rs. 27,999.00Regular priceUnit price / per -
AI-Deck Color Camera Module
Vendor:Regular price Rs. 2,199.00Regular priceUnit price / per -
AI-deck monocrome camera module
Vendor:Regular price Rs. 2,199.00Regular priceUnit price / per -
Flow deck v2
Vendor:Regular price Rs. 5,499.00Regular priceUnit price / per -
Crazyflie Bolt
Vendor:Regular price Rs. 21,999.00Regular priceUnit price / per -
Thrust upgrade bundle for Crazyflie 2.X
Vendor:Regular price Rs. 1,949.00Regular priceUnit price / perSold out -
Qi 1.2 wireless charging deck
Vendor:Regular price Rs. 3,849.00Regular priceUnit price / per -
7 mm DC-motor
Vendor:Regular price Rs. 439.00Regular priceUnit price / per -
Male long deck connector
Vendor:Regular price Rs. 219.00Regular priceUnit price / per -
250mAh LiPo battery
Vendor:Regular price Rs. 659.00Regular priceUnit price / per