Introducing the Expansion Board 3.0, compatible with the WiPy 2.0, WiPy 3.0, LoPy, LoPy4, SiPy, FiPy and GPy. NOTE: Does not include the WiPy Features USB and LiPo battery powered Custom PIC USB to serial converter with automatic bootloader mode LiPo battery charger (BQ24040), with options for two different charging currents (100mA and 450mA) TPS2115A with reverse voltage protection MicroSD card slot JST style battery connector Power LED and charge status LED One user LED and one user switch Button to enter into “safe mode” easily Battery voltage monitoring via the WiPy ADC Lots of jumpers to enable/disable features Size: 65 x 50 x 8mm

External WiFi Antenna and cable (non IP67). Includes Antenna, cable, washer and nut. Frequency Range: 2.4 2.5GHz VSWR: 2.0MAX Cable length: 10mm

Imagine 5 networks in one perfectly-formed, same-small-foot-print-as-WiPy- LoPy-and SiPy, IoT development board. MicroPython enabled. Featuring WiFi, Bluetooth, LoRa, Sigfox and dual LTE-M (CAT M1 and NBIoT) the FiPy gives access to all the world’s LPWAN networks on one tiny board. Get on with a board that gives you full flexibility during testing, install, deployment and even later when you want to switch real-time your airtime network provider. You can switch when the time is right for you or set some parameters that will do so automatically. Note: The LTE Antenna MUST always be used with LTE CAT M1 / NB1, or it could cause serious damage to the development board.   FiPy Features Powerful CPU Five networks: WiFi, BLE, cellular LTE-CAT M1/NB1, LoRa and Sigfox 1KM WiFi range MicroPython enabled Fits in a standard breadboard (with headers) Ultra-low power usage: a fraction compared to other connected microcontrollers Processing Espressif ESP32 SoC Dual processor and WiFi radio system on chip Networking processor handles the WiFi connectivity and the IPv6 stack Main processor is entirely free to run the user application An extra ULP-coprocessor that can monitor GPIOs, the ADC channels and control most of the internal peripherals during deep-sleep mode while only consuming 25uA Interfaces 2 x UART, 2 x SPI, I2C, micro SD card ANalog channels: 8_12 bit ADCs, 2_8 bit DAC Timers: 2_64 bit with PWM with up to 16 channels DMA on all peripherals GPIO: Up to 22 Hash / Encryption SHA, MD5, DES, AES WiFi Networking 802.11b/b/n 16mbps Bluetooth Low energy and classic RTC Running at 32KHz Range Node range: Up to 50km Security & Certifications SSL/TLS support up to 1.2  WPA Enterprise security AES encryption engine Memory RAM: 4MB Flash Memory: 8MB GPIO: Up to 22 Hardware floating point acceleration Python multi-threading Power Voltage Input: 3.3V  5.5V 3v3 output capable of sourcing up to 400mA Sigfox Operating Frequencies RCZ1 – 868MHz(Europe) RCZ2 – 902MHz (US, Canada and Mexico) RCZ3 – (Japan and Korea) RCZ4 – 920-922MHz (ANZ, Latin America and S-E Asia) Sigfox Specification Semtech SX1272 – Long Range, Low Power RF Transceiver 860-1000MHz with LoRa® Technology Class 0 device. Maximum Tx power: – 14dBm (Europe) – 22dBm (America) – 22dBm (Australia and New Zealand) Node range: Up to 50km Sigfox pre-certified (October 2016) Power Sigfox (Europe): 17mA in Rx mode, 47mA in Tx mode and 0.5uA in standby Sigfox (Australia, New Zealand and South America): 24mA in rX mode, 257 mA in Tx mode and 0.5uA in standby Bluetooth Networking Low energy and classic Compliant with Bluetooth v4.2 BR/EDR and BLE specification Class-1, Class-2 and Class-3 transmitter without external power amplifer Enhanced power control 10dBm transmitting power NZIF receiver with -98 dBm sensitivity Adaptive Frequency Hopping (AFH) Standard HCI based on SDIO/SPI/UART High speed UART HCI, up to 4 Mbps BT 4.2 controller and host stack Service Discover Protocol (SDP) General Access Profile (GAP) Security Manage Protocol (SMP) Bluetooth Low Energy (BLE) ATT/GATT HID All GATT-based profile supported SPP-Like GATT-based profile BLE Beacon A2DP/AVRCP/SPP, HSP/HFP, RFCOMM CVSD and SBC for audio codec Bluetooth Piconet and Scatternet LoRa Operating Frequencies 868MHz(Europe) at 14dBm maximum 915MHz (North and South America, Australia and New Zealand) at 20dBm maximum LoRa Specification Power consumption: 10mA Rx, 28mA Tx LoRaWAN stack – Class A and C devices Node range: Up to 40km Nano-gateway: Up to 22km (Capacity up to 100 nodes) LTE-M Operating Frequencies 17 bands supported from 699Mhz to 2170Mhz (Total world-wide support) Bands supported are currently: 1, 2, 3, 4, 5, 8, 12, 13, 14, 17, 18, 19, 20, 25, 26, 28, 66   LTE-M Specification One single chip for both CAT M1 and NB1 (yes, only one chip) 3GPP release 13 LTE Advanced Pro Supports narrowband LTE UE categories M1/NB1 Integrated baseband, RF, RAM memory and power management Reduced Tx power class option Peak power estimations: TX current = 420mA peak @1.5Watt RX current = 330mA peak @1.2Watt – Data rates: 300 kbps DL 375 kbps UL (LTE Cat M1 in 1.4 Mhz, HD-FDD) 40 kbps DL 55 kbps UL (LTE Cat M2 in 200 kHz, HD-FDD) Tx/Rx Frequencies Ports for LTE Bands Tx frequencies Rx frequencies Low bands 5, 8, 12, 13, 18, 19, 20, 28 699 to 915 MHz 729 to 960 MHz Mid bands 1, 2, 3, 4 1710 to 1980MHz 1805 to 2170 MHz WiFi Networking Up to 1km range 802.11b/g/n 16mbps Power: 12mA in active mode, 5uA in standby Size 55m x 20mm x 3.5mm (Without Headers)

The FiPy Multipack Bundle features the FiPy, the only 5-network (WiFi, BLE, LoRa, Sigfox and LTE-M) and MicroPython combo micro controller on the market today the perfect enterprise grade IoT platform for your connected Things. With the latest Espressif ESP32 SoC, the FiPy offers a perfect combination of power, friendliness and flexibility. Also included in the multipack is the LoRa/Sigfox Antenna and the LTE-M Antenna, plus your selection of expansion board or sensor shield. This Multipack allows you to get 1, 2 or 5 of FiPy and 1, 2 or 5 each of either Expansion Board, Pysense, Pytrack or Pyscan. Create and connect your things everywhere. Fast. Pyscan Features 3 axis 12-bit accelerometer Ambient light sensor RFID-NFC Chip USB port with serial access LiPo battery charger MicroSD card compatibility Ultra low power operation (~1uA in deep sleep) NFC / RFID Antenna included     Pytrack Features Super accurate GNSS Glonass GPS 3 axis 12-bit accelerometer USB port with serial access LiPo battery charger MicroSD ard compatibility Ultra low power operation (~1uA in deep sleep) Pysense Features Ambient light sensor Barometric pressure sensor Humidity sensor 3 axis 12-bit accelerometer Temperature sensor USB port with serial access LiPo battery charger MicroSD card compatibility Ultra low power operation (~1uA in deep sleep) Expansion Board Features USB and LiPo battery powered FT234XD USB to serial converter LiPo battery charger (BQ24040), with options for two different charging currents (100mA and 450mA) TPS2115A with reverse voltage protection MicroSD card slot Three female headers to easily plug in the WiPy 2.0, LoPy, SiPy, FiPy or GPy. JST style battery connector Power LED and charge status LED One user LED and one user switch Battery voltage monitoring via the WiPy ADC Lots of jumpers to enable/disable features FiPy Features Powerful CPu Five networks: WiFi, BLE, cellular LTE-CAT M1/NB1, LoRa and Sigfox 1KM WiFi range MicroPython enabled Fits in a standard breadboard (with headers) Ultra-low power usage: a fraction compared to other connected microcontrollers Processing Espressif ESP32 SoC Dual processor and WiFi radio system on chip Networking processor handles the WiFi connectivity and the IPv6 stack Main processor is entirely free to run the user application An extra ULP-coprocessor that can monitor GPIOs, the ADC channels and control most of the internal peripherals during deep-sleep mode while only consuming 25uA Interfaces 2 x UART, 2 x SPI, I2C, micro SD card ANalog channels: 8_12 bit ADCs, 2_8 bit DAC Timers: 2_64 bit with PWM with up to 16 channels DMA on all peripherals GPIO: Up to 22 Hash / Encryption SHA, MD5, DES, AES WiFi Networking 802.11b/b/n 16mbps Bluetooth Low energy and classic RTC Running at 32KHz Range Node range: Up to 50km Security & Certifications SSL/TLS support up to 1.2 WPA Enterprise security AES encryption engine Memory RAM: 4MB Flash Memory: 8MB GPIO: Up to 22 Hardware floating point acceleration Python multi-threading Power Voltage Input: 3.3V 5.5V 3v3 output capable of sourcing up to 400mA Sigfox Operating Frequencies RCZ1 – 868MHz(Europe) RCZ2 – 902MHz (US, Canada and Mexico) RCZ3 – (Japan and Korea) RCZ4 – 920-922MHz (ANZ, Latin America and S-E Asia) Sigfox Specification Semtech SX1272 – Long Range, Low Power RF Transceiver 860-1000MHz with LoRa® Technology Class 0 device. Maximum Tx power: 14dBm (Europe) 22dBm (America) 22dBm (Australia and New Zealand) Node range: Up to 50km Sigfox pre-certified (October 2016) Power Sigfox (Europe): 17mA in Rx mode, 47mA in Tx mode and 0.5uA in standb Sigfox (Australia, New Zealand and South America): 24mA in rX mode, 257 mA in Tx mode and 0.5uA in standby Bluetooth Networking Low energy and classic Compliant with Bluetooth v4.2 BR/EDR and BLE specification Class-1, Class-2 and Class-3 transmitter without external power amplifer Enhanced power control 10dBm transmitting power NZIF receiver with -98 dBm sensitivity Adaptive Frequency Hopping (AFH) Standard HCI based on SDIO/SPI/UART High speed UART HCI, up to 4 Mbps BT 4.2 controller and host stack Service Discover Protocol (SDP) General Access Profile (GAP) Security Manage Protocol (SMP) Bluetooth Low Energy (BLE) ATT/GATT HID All GATT-based profile supported SPP-Like GATT-based profile BLE Beacon A2DP/AVRCP/SPP, HSP/HFP, RFCOMM CVSD and SBC for audio codec Bluetooth Piconet and Scatternet LoRa Operating Frequencies 868MHz(Europe) at 14dBm maximum 915MHz (North and South America, Australia and New Zealand) at 20dBm maximum LoRa Specification Power consumption: 10mA Rx, 28mA Tx LoRaWAN stack – Class A and C devices Node range: Up to 40km Nano-gateway: Up to 22km (Capacity up to 100 nodes) Cellular Operating Frequencies 17 bands supports from 699Mhz to 2690Mhz (Total world-wide support) Bands supported are currently: 1, 2, 3, 4, 5, 8, 12, 13, 14, 17, 18, 19, 20, 25, 26, 28, 66 Cellular Specification One single chip for both CAT M1 and NB1 (yes, only one chip) 3GPP release 13 LTE Advanced Pro Supports narrowband LTE UE categories M1/NB1 Integrated baseband, RF, RAM memory and power management Reduced Tx power class option Peak power estimations: TX current = 420mA peak @1.5Watt RX current = 330mA peak @1.2Watt Data rates: 300 kbps DL 375 kbps UL (LTE Cat M1 in 1.4 Mhz, HD-FDD) 40 kbps DL 55 kbps UL (LTE Cat M2 in 200 kHz, HD-FDD) Tx/Rx Frequencies Ports for LTE Bands Tx frequencies Rx frequencies Low bands 5, 8, 12, 13, 18, 19, 20, 28 699 to 915 MHz 729 to 960 MHz Mid bands 1, 2, 3, 4 1710 to 1980MHz 1805 to 2170 MHz WiFi Networking Up to 1km range 802.11b/g/n 16mbps Power: 12mA in active mode, 5uA in standby Size 55m x 20mm x 3.5mm (Without Headers) Weight 7g 31g (Packaged) Pytrack Imagine a sensor shield which you can use with any of your Pycom multi-network modules! This is what we give you with Pysense and Pytrack a leg up to get you off to a great start really quickly. Pytrack Features Super accurate GNSS Glonass GPS 3 axis 12-bit accelerometer USB port with serial access LiPo battery charger MicroSD ard compatibility Ultra low power operation (~1uA in deep sleep) Location Services Supported GPS GLONASS Galileo QZSS Use with Pybytes Crafted by a group of Pycom back-end experts, the Pybytes platform will be everything there needs to be in place to gather, organise and display your data free of charge in the cloud. Regardless of whether you are a company, IoT system architect or an ambitious tech hobbyist we’ll soon have you connected. Size 55m x 35mm x 10mm Weight 11g (Standalone) Cellular Antenna External Cellular Antenna Kit covering both NB-IoT and Cat-M1 for use with the FiPy and GPy development boards. Specification Lte band 28/38*2 Frequency: 703~803/2520~2620(MHz) Antenna size: 75 x 21 (mm) PCB 0.6 mm Low bands (5, 8, 12, 13, 18, 19, 20, 28) Tx frequencies 699 to 915 MHz Rx frequencies 729 to 960 MHz Mid bands (1, 2, 3, 4) Tx frequencies 1710 to 1980MHz Rx frequencies 1805 to 2170 MHz LoRa / Sigfox Antenna Kit This universal LoRa & Sigfox Antenna Kit can be used with either the LoPy or the SiPy triple network IoT Development boards. The LoRa & Sigfox Antenna Kit Includes: External antenna. RF Cable Assemblies RP-SMA (Female) JK-IPEX MHF U.FL 1.13 100MM RP-SMA (Male) Tilt Swivel 1/2 Wave Whip antenna   NOTE: Using a LoRa or Sigfox radio on LoPy or SiPy without the external antenna can lead to damage of the device and is therefore not recommended. So, if it’s not this one, please make sure you get one somewhere else. NOTE: For waterproofing please also order the special IP67 antenna connector cable.

The G01 is the GPy OEM module. It’s just like the GPy but with a few bits less to make it easy to integrate. Triple network module: Cellular LTE-CAT M1/NB1, WiFi and Bluetooth. Fits on the Pycom OEM Reference Board. Not included in G01 Voltage regulatorReverse power supply protectionAntenna switchSMD antennau.fl connectorsReset switchLEDHeadersA few passive components You will be given full technical support to design-in / integrate the module onto your product PCB. Everything else is the same and you can load all your applications both on your G01 modules and on your GPy. Supplied in high volume assembly format (with SMT pads). Also, there is no packaging to unwrap and do away with. The G01 can be supplied and used straight from hermetically sealed reels. It’s great for your scalable deployments and is delivered CE, FCC, IC and RCM certified. Whilst Pycom plans carefully to ensure modules are always in stock, in the eventuality of these being “Out-Of-Stock”, then deliveries will be circa 8-12 weeks from order receipt. Contact us on sales@pycom.io for more details. G01 Features Powerful CPU 1KM Wifi Range MicroPython enabled Fits on the Pycom OEM Reference Board. Ultra-low power usage: a fraction compared to other connected micro controllers LTE-M Operating Frequencies 34 bands supported from 699Mhz to 2690Mhz (Total world-wide support) LTE-M Specification One single chip for both CAT M1 and NB1 (yes, only one chip) 3GPP release 13 LTE Advanced Pro Supports narrowband LTE UE categories M1/NB1 Integrated baseband, RF, RAM memory and power management Reduced Tx power class option Peak power estimations: TX current = 420mA peak @1.5Watt RX current = 330mA peak @1.2Watt Data rates: 300 kbps DL 375 kbps UL (LTE Cat M1 in 1.4 Mhz, HD-FDD) 40 kbps DL 55 kbps UL (LTE Cat M2 in 200 kHz, HD-FDD) Band support for: Interfaces 2 x UART, 2 x SPI, I2C, I2S, micro SD card Analog channels: 8×12 bit ADCs, 2×8 bit DAC Timers: 2×64 bit with PWM with up to 16 channels DMA on all peripherals Power Voltage Input: 3.3V regulated Processing Espressif ESP32 SoC Dual processor WiFi radio System on Chip. Network processor handles the WiFi connectivity and the IPv6 stack Main processor is entirely free to run the user application An extra ULP-coprocessor that can monitor GPIOs, the ADC channels and control most of the internal peripherals during deep-sleep mode while only consuming 25uA Security & Certifications SSL/TLS support up to 1.2 WPA Enterprise security AES encryption engine Memory RAM: 4MB Flash Memory: 8MB GPIO: Up to 22 Hardware floating point acceleration Python multi-threading Hash / encryption SHA, MD5, DES, AES WiFi Networking 802.11b/g/n 16mbps Bluetooth Low energy and classic RTC Running at 32KHz

With WiFi, BLE and cellular LTE CAT M1/NB1, the GPy is the latest Pycom triple-bearer MicroPython enabled micro controller on the market today the perfect enterprise grade IoT platform for your connected Things. Create and connect your things everywhere, fast. Get on with a board that gets you into the newly available LTE CAT M1 / NB1 networks. The GPy gives you full flexibility during testing, install, deployment and is delivered RCM, IC, CE and FCC certified. With WiFi, BLE and cellular LTE CAT M1/NB1, the GPy is the latest Pycom triple-bearer MicroPython enabled micro controller on the market today the perfect enterprise grade IoT platform for your connected Things. Create and connect your things everywhere, fast. Note: The Cellular Antenna MUST always be used with LTE CAT M1 / NB1, or it could cause serious damage to the development board.     GPy Features Powerful CPU 1KM WiFi range MicroPython enabled Fits in a standard breadboard (with headers) Ultra-low power usage: fraction compared to other connected microcontrollers Tx/Rx Frequencies Ports for LTE Bands Tx frequencies Rx frequencies Low bands 5, 8, 12, 13, 18, 19, 20, 28 699 to 915 MHz 729 to 960 MHz Mid bands 1, 2, 3, 4 1710 to 1980MHz 1805 to 2170 MHz Cellular Operating Frequencies 17 bands supported from 699Mhz to 2170Mhz (Total world-wide support) Bands supported are currently: 1, 2, 3, 4, 5, 8, 12, 13, 14, 17, 18, 19, 20, 25, 26, 28, 66   Cellular Specification One single chip for both CAT M1 and NB1 3GPP release 13 LTE Advanced Pro Supports narrowband LTE UE categories M1/NB1 Integrated baseband, RF, RAM memory and power management Reduced Tx power class option Peak power estimations: TX current = 420mA peak @1.5Watt RX current = 330mA peak @1.2Watt Data rates: 300kbps DL 375 kbps UL (LTE Cat M1 in 1.4Mhz in 1.4 Mhz, HD-FDD) 40 kbps DL 55kbps UL (LTE Cat M2 in 200 kHz, HD-FDD) Interfaces 2 x UART, 2 x SPI, I2C, I2S micro SD card Analog channels: 8_12 bit ADCs, 2_8 bit DAC Timers: 2_64 bit with PWM with up to 16 channels DMA on all peripherals Power Voltage Input: 3.3V 5.5V 3v3 output capable of sourcing up to 400mA Processing Espressif ESP32 SoC Dual processor WiFi radio system on chip Network processor handles the WiFi connectivity and the IPv6 stack Main processor is entirely free to run the user application An extra ULP-coprocessor that can monitor GPIOs, the ADC channels and control most of the internal peripherals during deep-sleep mode while only consuming 25uA Security & Certifications  SSL/TLS support up to 1.2 WPA Enterprise security AES encryption engine Memory RAM: 4MB Flash Memory: 8MB GPIO: Up to 22 Hardware floating point acceleration Python multi-threading Hash / Encryption SHA, MD5, DES, AES WiFi Networking 802.11b/g/n 16mbps Bluetooth Low energy and classic RTC Running at 32KHz Size 55mm x 20mm x 3.5mm (Without Headers)

The GPy Expansion Board Bundle features the GPy, the only LTE CAT M1 / NB1 and MicroPython combo micro controller on the market today – the perfect enterprise grade IoT platform for your connected Things. With the latest Espressif ESP32 SoC, the GPy offers a perfect combination of power, friendliness and flexibility. Also included in this bundle is the LTE-M Antenna and your choice of expansion board or sensor shield. This Multipack allows you to get 1, 2 or 5 of GPy and 1, 2 or 5 each of either Expansion Board, Pysense, Pytrack or Pyscan. Create and connect your things everywhere. Fast. Pyscan Features 3 axis 12-bit accelerometer Ambient light sensor RFID-NFC Chip USB port with serial access LiPo battery charger MicroSD card compatibility Ultra low power operation (~1uA in deep sleep) NFC / RFID Antenna included Pytrack Features Super accurate GNSS Glonass GPS 3 axis 12-bit accelerometer USB port with serial access LiPo battery charger MicroSD ard compatibility Ultra low power operation (~1uA in deep sleep) Pysense Features Ambient light sensor Barometric pressure sensor Humidity sensor 3 axis 12-bit accelerometer Temperature sensor USB port with serial access LiPo battery charger MicroSD card compatibility Ultra low power operation (~1uA in deep sleep) Expansion Board Features USB and LiPo battery powered FT234XD USB to serial converter LiPo battery charger (BQ24040), with options for two different charging currents (100mA and 450mA) TPS2115A with reverse voltage protection MicroSD card slot Three female headers to easily plug in the WiPy 2.0, LoPy, SiPy, FiPy or GPy. JST style battery connector Power LED and charge status LED One user LED and one user switch Battery voltage monitoring via the WiPy ADC Lots of jumpers to enable/disable features GPy Features Powerful CPU 1KM WiFi range MicroPython enabled Fits in a standard breadboard (with headers) Ultra-low power usage: fraction compared to other connected microcontrollers Tx/Rx Frequencies Ports for LTE Bands Tx frequencies Rx frequencies Low bands 5, 8, 12, 13, 18, 19, 20, 28 699 to 915 MHz 729 to 960 MHz Mid bands 1, 2, 3, 4 1710 to 1980MHz 1805 to 2170 MHz     Cellular Operating Frequencies 17 bands supported from 699Mhz to 2690Mhz (Total world-wide support) Bands supported are currently: 1, 2, 3, 4, 5, 8, 12, 13, 14, 17, 18, 19, 20, 25, 26, 28, 66     Cellular Specification One single chip for both CAT M1 and NB1 3GPP release 13 LTE Advanced Pro Supports narrowband LTE UE categories M1/NB1 Integrated baseband, RF, RAM memory and power management Reduced Tx power class option Peak power estimations: TX current = 420mA peak @1.5Watt RX current = 330mA peak @1.2Watt Data rates: 300kbps DL 375 kbps UL (LTE Cat M1 in 1.4Mhz in 1.4 Mhz, HD-FDD) 40 kbps DL 55kbps UL (LTE Cat M2 in 200 kHz, HD-FDD) Interfaces 2 x UART, 2 x SPI, I2C, I2S micro SD card Analog channels: 8_12 bit ADCs, 2_8 bit DAC Timers: 2_64 bit with PWM with up to 16 channels DMA on all peripherals Power Voltage Input: 3.3V 5.5V 3v3 output capable of sourcing up to 400mA Processing Espressif ESP32 SoC Dual processor WiFi radio system on chip Network processor handles the WiFi connectivity and the IPv6 stack Main processor is entirely free to run the user application An extra ULP-coprocessor that can monitor GPIOs, the ADC channels and control most of the internal peripherals during deep-sleep mode while only consuming 25uA Security & Certifications SSL/TLS support up to 1.2 WPA Enterprise security AES encryption engine Memory RAM: 4MB Flash Memory: 8MB GPIO: Up to 22 Hardware floating point acceleration Python multi-threading Hash / Encryption SHA, MD5, DES, AES WiFi Networking 802.11b/g/n 16mbps Bluetooth Low energy and classic RTC Running at 32KHz Size 55mm x 20mm x 3.5mm (Without Headers) Weight 7g 31g Location Services Supported GPS GLONASS Galileo QZSS Use with Pybytes Crafted by a group of Pycom back-end experts, the Pybytes platform will be everything there needs to be in place to gather, organise and display your data free of charge in the cloud. Regardless of whether you are a company, IoT system architect or an ambitious tech hobbyist we’ll soon have you connected. Size 55m x 35mm x 10mm Weight 11g (Standalone) Cellular Antenna External LTE-M Antenna Kit for use with the FiPy and GPy development boards. Specification Lte band 28/38*2 Frequency: 703~803/2520~2620(MHz) Antenna size: 75 x 21 (mm) PCB 0.6 mm Low bands (5, 8, 12, 13, 18, 19, 20, 28) Tx frequencies 699 to 915 MHz Rx frequencies 729 to 960 MHz Mid bands (1, 2, 3, 4) Tx frequencies 1710 to 1980MHz Rx frequencies 1805 to 2170 MHz

IP67 antenna cable to help waterproof your outdoor IoT applications. Use with Sigfox/LoRa/External WiFi Antenna sold on this site. Includes nut, washer and rubber ring. Perfect for use with IP67 cases Product Performance: 50R Impedance 60Vrms Maximum working voltage 200Vrms Minimum dielectric withstanding voltage 500MR Minimum Insulator resistance IP67 Protection rating Cable length: 100mm from rear of SMA connector to center of UFL connector Does not include the Antenna which may be purchased separately.

This is the IP67 case for Pysense and Pytrack. Space available for Pycom module (whether you are using a WiPy 2.0, LoPy, SiPy, GPy or FiPy), Pycom shield (Pysense or Pytrack) and a LiPo battery. Waterproofing by using silicone gasket. UV resistant case. Mountable onto external surface/brackets by opening the blind lids. Dimensions External case dimensions: W 75 x D 75 x H 35 mm. Internal available space: W 67 x 46 x H 25.4 mm.

The L01 is the LoPy OEM module. It works just like the LoPy but we’ve trimmed a few bits to make it super easy to integrate. Triple network module: LoRa, WiFi and Bluetooth. Fits on the Pycom OEM Reference Board. Drawings and reference design The drawings can be found here. The pinoutsheet is available here. Not included in L01 Voltage regulator Reverse power supply protection Antenna switch SMD antenna u.fl connectors Reset switch LED Headers A few passive components You will be given full technical support to design-in / integrate the module onto your product PCB. Everything else is the same and you can load the same applications on your L01 and on your LoPy. Supplied in high volume assembly format (with SMT pads). Also, there’s no packaging to unwrap and do away with. The module can be supplied and used straight from its hermetically sealed reels. The L01 is both CE, FCC, IC and RCM certified. Whilst Pycom plans carefully to ensure modules are always in stock, in the eventuality of these being “Out-Of-Stock”, then deliveries will be circa 8-12 weeks from order receipt. Contact us on sales@pycom.io for more details. L01 Features Powerful CPU, BLE and state of the art WiFi radio Can also double up as a Nano LoRa gateway MicroPython enabled Fits on the Pycom OEM Reference Board – Ultra-low power usage: a fraction compared to other connected micro controllers Processing Espressif ESP32 chipset Dual processor WiFi radio System on Chip. Network processor handles the WiFi connectivity and the IPv6 stack. Main processor is entirely free to run the user application. An extra ULP-coprocessor that can monitor GPIOs, the ADC channels and control most of the internal peripherals during deep-sleep mode while only consuming 25uA. Operating Frequencies 868 MHz (Europe) at 14dBm maximum 915 MHz (North and South America, Australia and New Zealand) at 20dBm maximum Range Specification Node range: Up to 40km Nano-Gateway: Up to 22km Nano-Gateway Capacity: Up to 100 nodes Interfaces 2 x UART, 2 x SPI, I2C, I2S, micro SD card Analog channels: 8×12 bit ADCs Timers: 4×16 bit with PWM and input capture DMA on all peripherals GPIO: Up to 24 Security & Certifications SSL/TLS support WPA Enterprise security FCC – 2AJMTL01XXX CE 0700 Memory RAM: 4MB Flash Memory: 8MB Hardware floating point acceleration Python multi-threading Hash / encryption SHA, MD5, DES, AES WiFi 802.11b/g/n 16mbps Bluetooth Low energy and classic RTC Running at 32KHz Power Voltage Input: 3.3V regulated WiFi: 12mA in active mode, 5uA in standby Lora: 15mA in active mode, 10uA in standby LoRa Specification Semtech LoRa transceiver SX1272 LoRaWAN stack Class A and C devices

The L04 is the LoPy4 OEM module. It works just like the LoPy4 but we’ve trimmed a few bits to make it super easy to integrate. Quadruple network module: WiFi, Bluetooth, LoRa and Sigfox. Not included in L04 Voltage regulator Reverse power supply protection Antenna switch SMD antenna u.fl connectors Reset switch LED Headers A few passive components You will be given full technical support to design-in / integrate the module onto your product PCB. Everything else is the same and you can load the same applications on your L04 and on your LoPy4. Supplied in high volume assembly format (with SMT pads). Also, there’s no packaging to unwrap and do away with. The module can be supplied and used straight from its hermetically sealed trays. The L04 is both CE, FCC, IC and RCM certified. Contact us on sales@pycom.io for more details. NOTE: The L04 includes 1-year of Sigfox connectivity. NOTE: If you are purchasing the L04 and wish to connect via USB to your computer, you will also need to purchase the OEM Reference Board and either the Expansion Board 3.0, Pysense or Pytrack. L04 Features Powerful CPU, BLE and state of the art WiFi radio Can also double up as Nano LoRa gateway MicroPython enabled Fits on the Pycom OEM Reference Board Ultra-low power usage: a fraction compared to other connected micro controllers Processing  Espressif ESP32 chipset Dual processor WiFi radio System on chip Network processor handles the WiFi connectivity and the IPv6 stack Main processor is entirely free to run the user application An extra ULP-coprocessor that can monitor GPIOs, the ADC channels and control most of the internal peripherals during deep-sleep mode while only consuming 25uA Sigfox Operating Frequencies RCZ1  868MHz (Europe) RCZ2  902MHz (US, Canada and Mexico) RCZ3  (Japan and Korea) CZ4  920-922MHz (ANZ, Latin America and S-E Asia) Sigfox Specification Class 0 device. Maximum Tx power: 14dBm (Europe) 20dBm (America) 20dBm (Australia and New Zealand) Node range: Up to 50km Sigfox certified LoRa Specification Semtech LoRa transceiver SX1276 LoRaWAN stack Class A and C devices LoRa Operating Frequencies 868 MHz (Europe) at 14dBm maximum 915 MHz (North and South America, Australia and New Zealand) at 20dBm maximum 433 MHz (Europe) at 10dBm maximum 470 – 510 MHz (China) at 14dBm maximum Range Specification Node range: Up to 40km Nano-gateway: Up to 22km Nano-gateway capacity: Up to 100 nodes Interfaces 2 x UART, 2 x SPI, I2C, I2S, micro SD card Analog channels: 8_12 bit ADCs Timers: 4_16 bit with PWM and input capture DMA on all peripherals GPIO: Up to 24 Security & Certifications SSL/TLS support WPA Enterprise security FCC 2AJMTL04XXX CE 0700 Memory RAM: 4MB External flash: 8MB Hardware floating point acceleration Python multi-threading Hash / encryption SHA, MD5, DES, AES WiFi 802.1b/g/n 16mbps Bluetooth Low energy and classic RTC Running at 32KHz Power Input: 3.3V 5.5V 3v3 output capable of sourcing up to 400mA WiFi: 12mA in active mode, 5uA in standby LoRa: 15mA in active mode, 1-uA in standby Sigfox (Europe): 12mA in Rx mode, 42mA in Tx mode and 0.5uA in standby Sigfox (Australia, New Zealand and South America): 12mA in Rx mode, 120 mA in Tx mode and 0.5uA in standby Size 55mm x 20mm x 3.5mm (Without Headers)

1 YEAR OF SIGFOX CONNECTIVITY INCLUDEDThe LoPy4 is a quadruple bearer MicroPython enabled development board (LoRa, Sigfox, WiFi, Bluetooth) perfect enterprise grade IoT platform for your connected Things. With the latest Espressif chipset the LoPy4 offers a perfect combination of power, friendliness and flexibility. Create and connect you things everywhere. Fast. If you are purchasing the LoPy4 and wish to connect via USB to your computer, you will also need to purchase either the Expansion Board 2.0, Pysense or Pytrack. The LoPy4 is a compact quadruple network MicroPython enabled development board (LoRa, Sigfox, WiFi, Bluetooth). It’s the perfect enterprise grade IoT platform for your connected Things. With the latest Espressif ESP32 chipset the LoPy4 offers a perfect combination of power, friendliness and flexibility. Create and connect you things everywhere. Fast. The LoPy4 can act as a LoRa nano gateway and a multi-bearer (LoRa, Sigfox, WiFi and BLE) development platform suitable for all LoRa and Sigfox networks around the globe. It is programmable with MicroPython and the Pymakr plugins for fast IoT application development, easy programming in-field and extra resilience with network failover. You can also configure the LoPy4 in raw LoRa mode to send packets directly between LoPy4’s. The best blend of speed to deployment and access to new LPWAN networks rolling out across Europe, USA, Africa and India. The LoPy4 is CE, FCC approved, LoRaWAN and Sigfox certified. The board ships with or without male headers mounted as seen on the pictures. The LoPy4 includes 1-year of Sigfox connectivity – strictly for development purposes only. NOTE: SIGFOX CONNECTIVITY IS INCLUDED FOR 12 MONTHS FROM FIRST USE OF DEVICE FOR DEVELOPMENT UNITS. THIS DOES NOT INCLUDE LARGER DEPLOYMENTS/COMMERCIAL USE WHERE A PAYABLE SERVICE WILL BE REQUIRED. CONTACT PYCOM FOR PRICING NOTE: Using the LoRa or Sigfox radio without the external antenna can lead to damage of the device and is therefore not recommended. If you are purchasing the LoPy4 and wish to connect via USB to your computer, you will also need to purchase either the Expansion Board 2.0, Pysense or Pytrack. LoPy4 Features Powerful CPU, BLE and state of the art WiFi radio Can also double up as Nano LoRa gateway MicroPython enabled Fits in a standard breadboard (with headers) Ultra-low power usage: a fraction compared to other connected micro controllers Processing Espressif ESP32 chipset Dual processor WiFi radio System on chip Network processor handles the WiFi connectivity and the IPv6 stack Main processor is entirely free to run the user application An extra ULP-coprocessor that can monitor GPIOs, the ADC channels and control most of the internal peripherals during deep-sleep mode while only consuming 25uA Sigfox Operating Frequencies RCZ1 – 868MHz (Europe) RCZ2 – 902MHz (US, Canada and Mexico) RCZ3 – (Japan and Korea) RCZ4 – 920-922MHz (ANZ, Latin America and S-E Asia) Sigfox Specification Class 0 device. Maximum Tx power: 14dBm (Europe) 20dBm (America) 20dBm (Australia and New Zealand) Node range: Up to 50km Sigfox certified LoRa Specification Semtech LoRa transceiver SX1276 LoRaWAN stack Class A and C devices LoRa Operating Frequencies 868 MHz (Europe) at 14dBm maximum 915 MHz (North and South America, Australia and New Zealand) at 20dBm maximum 433 MHz (Europe) at 10dBm maximum 470 – 510 MHz (China) at 14dBm maximum LoRa Range Specification Node range: Up to 40km Nano-gateway: Up to 22km Nano-gateway capacity: Up to 100 nodes Interfaces 2 x UART, SPI, 2 x I2C, I2S, micro SD card Analog channels: 8_12 bit ADCs Timers: 4_16 bit with PWM and input capture DMA on all peripherals GPIO: Up to 24 Security & Certifications SSL/TLS support WPA Enterprise security FCC 2AJMTLOPY4R CE 0700 Memory RAM: 4MB External flash: 8MB Hardware floating point acceleration Python multi-threading Hash / encryption SHA, MD5, DES, AES WiFi 802.1b/g/n 16mbps Bluetooth Low energy and classic RTC Running at 32KHz Power Input: 3.3V 5.5V 3v3 output capable of sourcing up to 400mA WiFi: 12mA in active mode, 5uA in standby LoRa: 15mA in active mode, 1-uA in standby Sigfox (Europe): 12mA in Rx mode, 42mA in Tx mode and 0.5uA in standby Sigfox (Australia, New Zealand and South America): 12mA in Rx mode, 120 mA in Tx mode and 0.5uA in standby Size 55mm x 20mm x 3.5mm (Without Headers)  

The LoPy4 Multipack Bundle features the LoPy4, the only 4-network (WiFi, BLE, LoRa, and Sigfox) and MicroPython combination controller on the market today the perfect enterprise grade IoT platform for your connected Things. With the latest Espressif ESP32 SoC, the LoPy4 offers a perfect combination of power, friendliness and flexibility. Also included in the multipack is the LoRa/Sigfox Antenna and your selection of expansion board or sensor shield. This Multipack allows you to get 1, 2 or 5 of LoPy4 and 1, 2 or 5 each of either Expansion Board, Pysense, Pytrack or Pyscan. Create and connect your things everywhere. Fast. Pyscan Features 3 axis 12-bit accelerometer Ambient light sensor RFID-NFC Chip USB port with serial access LiPo battery charger MicroSD card compatibility Ultra low power operation (~1uA in deep sleep) NFC / RFID Antenna included Pytrack Features Super accurate GNSS Glonass GPS 3 axis 12-bit accelerometer USB port with serial access LiPo battery charger MicroSD ard compatibility Ultra low power operation (~1uA in deep sleep) Pysense Features Ambient light sensor Barometric pressure sensor Humidity sensor 3 axis 12-bit accelerometer Temperature sensor USB port with serial access LiPo battery charger MicroSD card compatibility Ultra low power operation (~1uA in deep sleep) Expansion Board Features USB and LiPo battery powered FT234XD USB to serial converter LiPo battery charger (BQ24040), with options for two different charging currents (100mA and 450mA) TPS2115A with reverse voltage protection MicroSD card slot Three female headers to easily plug in the WiPy 2.0, LoPy, SiPy, FiPy or GPy. JST style battery connector Power LED and charge status LED One user LED and one user switch Battery voltage monitoring via the WiPy ADC Lots of jumpers to enable/disable feature LoPy4 Features Powerful CPU, BLE and state of the art WiFi radio Can also double up as Nano LoRa gateway MicroPython enabled Fits in a standard breadboard (with headers) Ultra-low power usage: a fraction compared to other connected micro controllers Processing Espressif ESP32 chipset Dual processor WiFi radio System on chip Network processor handles the WiFi connectivity and the IPv6 stack Main processor is entirely free to run the user application An extra ULP-coprocessor that can monitor GPIOs, the ADC channels and control most of the internal peripherals during deep-sleep mode while only consuming 25uA Sigfox Operating Frequencies RCZ1 ? 868MHz (Europe) RCZ2 ? 902MHz (US, Canada and Mexico) RCZ3 ? (Japan and Korea) RCZ4 ? 920-922MHz (ANZ, Latin America and S-E Asia) Sigfox Specification Class 0 device. Maximum Tx power: 14dBm (Europe) 20dBm (America) 20dBm (Australia and New Zealand) Node range: Up to 50km Sigfox certified LoRa Specification Semtech LoRa transceiver SX1272 LoRaWAN stack Class A and C devices   LoRa Operating Frequencies 868 MHz (Europe) at 14dBm maximum 915 MHz (North and South America, Australia and New Zealand) at 20dBm maximum 433 MHz (Europe) at 10dBm maximum 470 – 510 MHz (China) at 14dBm maximum   Range Specification Node range: Up to 40km Nano-gateway: Up to 22km Nano-gateway capacity: Up to 100 nodes Interfaces 2 x UART, 2 x SPI, I2C, I2S, micro SD card Analog channels: 8_12 bit ADCs Timers: 4_16 bit with PWM and input capture DMA on all peripherals GPIO: Up to 24 Security & Certifications SSL/TLS support WPA Enterprise security FCC 2AJMTLOPY4R CE 0700 Memory RAM: 4MB External flash: 8MB Hardware floating point acceleration Python multi-threading Hash / encryption SHA, MD5, DES, AES WiFi 802.1b/g/n 16mbps Bluetooth Low energy and classic RTC Running at 32KHz Power Input: 3.3V ? 5.5V 3v3 output capable of sourcing up to 400mA WiFi: 12mA in active mode, 5uA in standby LoRa: 15mA in active mode, 1-uA in standby Sigfox (Europe): 17mA in Rx mode, 47mA in Tx mode and 0.5uA in standby Sigfox (Australia, New Zealand and South America): 24mA in Rx mode, 257 mA in Tx mode and 0.5uA in standby Size 55mm x 20mm x 3.5mm (Without Headers) Weight 7g 31g (Packaged) LoRa / Sigfox Antenna Kit External antenna. RF Cable Assemblies RP-SMA (Female) JK-IPEX MHF U.FL 1.13 100MM RP-SMA (Male) Tilt Swivel 1/2 Wave Whip antenna Weight: 21g Compatible with Pymakr plugins. The LoPy4 includes 1-year of Sigfox connectivity.NOTE: Using the LoRa or Sigfox radio without the external antenna can lead to damage of the device and is therefore not recommended. PLEASE NOTE: Pycom modules are powered by the NEW and FEATURE PACKED Espressif ESP32 chip. As a result our firmware is evolving constantly as the ESP32 IDF matures. Regular firmware updates are therefore provided. If you are purchasing the LoPy4 and wish to connect via USB to your computer, you will also need to purchase either the Expansion Board 2.0, Pysense or Pytrack.

External LTE-M Antenna Kit for use with the FiPy and GPy development boards. Specification Frequency: 703~803/2520~2620(MHz) Antenna size: 75 x 21 (mm) PCB 0.6 mm LTE Low bands (5, 8, 12, 13, 18, 19, 20, 28) Tx frequencies 699 to 915 MHz Rx frequencies 729 to 960 MHz LTE Mid bands (1, 2, 3, 4) Tx frequencies 1710 to 1980MHz Rx frequencies 1805 to 2170 MHz

Reference Board used to mount either Pycom OEM modules. Provides the same functionality and pin-out as the developer version of the modules and can be mounted straight-out-of the box. Contains: RGB LED 5V to 3.3V DC-DC switching regulator u.fl connector for the LoRa antenna Dual antenna options for WiFi/Bluetooth Male header pins Note: L01 not Included Find support on our documentation: docs.pycom.io And community help on our forum: forum.pycom.io

Pycase Blue is a neat case developed specifically for a Pycom development board and expansion board combo. Holds Development Board, Expansion Board, Antenna and there’s even room for a small battery. The Pycase is compatible with LoPy, WiPy, FiPy, SiPy or GPy with an expansion board and attached antenna. Pycase Blue Size 65mm x 77mm x 28.5mm Note: that the Expansion board featured in the photos are NOT included with the Pycase sale and must be purchased separately. Featured for illustration purposes only. Colour may vary slightly. Note: Not compatible with the Deep Sleep Mode shield.

Pycase Clear is a small, completely transparent case developed specifically for a Pycom development board and expansion board combo. Holds Development Board, Expansion Board, Antenna and there’s even room for a small battery. The Pycase is compatible with LoPy, WiPy, FiPy, SiPy or GPy with an expansion board and attached antenna. Pycase Clear Size 65mm x 77mm x 28.5mm Note: that the Expansion board featured in the photos are NOT included with the Pycase sale and must be purchased separately. Featured for illustration purposes only. Colour may vary slightly. Note: Not compatible with the Deep Sleep Mode shield.

Pygate is Pycom’s latest hardware tech portfolio addition. This is a new super low-cost 8-channel LoRaWAN gateway that comes in the shape of a shield. It’s got the well-known form factor from our other shields and you can connect your much loved WiPy3, LoPy4 or a GPy to it. Hook in your Pycom development boards up and you have yourself a nifty little decentralized IoT network in one go. Pygate also fits inside the Universal IP67 Case so you don’t have to limit yourself to indoors. Connect a WiPy3, LoPy4 or a GPy to this shield and then hook in all your other Pycom devices and you have yourself a nifty little decentralised IoT network in one go. Check out the optional Power over Ethernet via daughter board. Coming soon Features Dual SX1257 transceivers for a total of 8 channels support Frequencies: 863-870 MHz and 902-928 MHz Baseband processor: SX1308 Compatible with WiPy3.0, GPy and LoP4 Ultra-low power standby mode Ethernet with PoE via the optional daughter board Powered via USB, LiPo Battery and Ethernet via the optional daughter board LiPo battery charging via the USB port USB to serial connection for the Pycom module with auto-programming features Dimensions: 65 (W) x 50 (L) x 8 (H) mm(Same small form factor as the Expansion Board v3.0/v3.1) Fits the universal IP67 Case for outdoor use   PoE Adapter Specification (This is optional) PoE (Power Over Ethernet) with 1.5A current delivery. It can provide power for the Pygate and the Pycom module attached to it. 10BASE-T and 100BASE-TX Physical Layer Support Auto-Negotiation: 10/100 Mbps Full- and HalfDuplex Plug and play compatibility with Pygate. Works transparently using the TCP/IP stack embedded into our MicroPython modules. Dimensions: 21 (W) x 55 (L) x 32 (H) mm   Important Note: Pygate is not compatible with FiPy.

NOTE:* Please note purchasing the case does not include Pygate or the antenna connectors displayed on the photo. Pygate is Pycom’s new super low-cost 8-channel LoRaWAN gateway that comes in the shape of a shield and this is the only case you will ever need to protect / embellish / show off your new bit of Tech!

Non-cellular multi-purpose wearable device featuring Pymesh and… LoRa, WiFi and Bluetooth OLED (Piezo touch screen) GPS Accelerometer State of the art antennas LiPo battery QI wireless charging 6 exposed pins (2 charging/4 universal in/out) Meet the PyGo1 which is in essence a LoPy4 module on steroids! We packed the LoPy4 in an IP67 case, gave it an OLED (Piezo touch screen sensing), a GPS, an accelerometer, some state of the art antennas, a LiPo battery and a QI wireless charging solution. The PyGo1 features six exposed pins: 2 for power and 4 universal inputs/outputs with digital/analogue capabilities so that you can connect different types of sensors and actuators. Developers can physically connect Things and sensors to a PyGo! And yes, before you ask, rest assured, we will be adding electrical circuit protection to ensure PyGo can have a bath and still retain its cool IP67 protection. Best of all, the PyGo modules are fully programmable using existing Pycom IDE such as Pymakr and can link up with any other Pycom modules. We launched the PyGo modules with the ability to mesh together at distance of up to 12KM. PyGo1 includes WiFi, Bluetooth, LoRa and Sigfox. The PyGo1 gives access to all the world’s LPWAN networks on one tiny board. The PyGo1 includes 1-year of Sigfox connectivity. If you are purchasing the PyGo1 and wish to connect via USB to your computer, you will also need to purchase either the PyGo cradle.   PyGo1 Features Powerful CPU Five networks: WiFi, BLE, LoRa, LoRa (MESH) and Sigfox Up to 1KM WiFi range MicroPython enabled Electrical circuit protection Ultra-low power usage: a fraction compared to other connected microcontrollers Pymakr IDE supported Pylife Application with IFTTT style environment for light programming OLED IP67 rated Qi Wireless charging Processing Espressif ESP32 SoC Dual processor and WiFi radio system on chip Networking processor handles the WiFi connectivity and the IPv6 stack Main processor is entirely free to run the user application An extra ULP-coprocessor that can monitor GPIOs, the ADC channels and control most of the internal peripherals during deep-sleep mode while only consuming 25uA Interfaces Analog channels: 8_12 bit ADCs, 2_8 bit DAC Timers: 2_64 bit with PWM with up to 16 channels DMA on all peripherals 2 Pins (Power) GPIO: 4 analog input (0-3.3V 12bit SAR ADC) and digital (3.3V logic) input/output pins. Hash / Encryption SHA, MD5, DES, AES WiFi Networking 802.11b/b/n 16mbps Bluetooth Low energy and classic RTC Running at 32KHz Range Node range: Up to 50km Security & Certifications SSL/TLS support up to 1.2 WPA Enterprise security AES encryption engine Memory RAM: 64Mbit Flash Memory: 8MB Hardware floating point acceleration Python multi-threading Power LiPo battery: 420mAh LiPo 4.2V Pymesh Connect upto 200 devices in a mesh using our LoRamesh technology Sigfox Operating Frequencies RCZ1 – 868MHz(Europe) RCZ2 – 902MHz (US, Canada and Mexico) RCZ3 – (Japan and Korea) RCZ4 – 920-922MHz (ANZ, Latin America and S-E Asia) Sigfox Specification Semtech SX1272 – Long Range, Low Power RF Transceiver 860-1000MHz with LoRa® Technology Class 0 device. Maximum Tx power: – 14dBm (Europe) – 22dBm (America) – 22dBm (Australia and New Zealand) Node range: Up to 50km Sigfox pre-certified (October 2016) Power Sigfox (Europe): 17mA in Rx mode, 47mA in Tx mode and 0.5uA in standby Sigfox (Australia, New Zealand and South America): 24mA in rX mode, 257 mA in Tx mode and 0.5uA in standby Bluetooth Networking Low energy and classic Compliant with Bluetooth v4.2 BR/EDR and BLE specification Class-1, Class-2 and Class-3 transmitter without external power amplifer Enhanced power control 10dBm transmitting power NZIF receiver with -98 dBm sensitivity Adaptive Frequency Hopping (AFH) Standard HCI based on SDIO/SPI/UART High speed UART HCI, up to 4 Mbps BT 4.2 controller and host stack Service Discover Protocol (SDP) General Access Profile (GAP) Security Manage Protocol (SMP) Bluetooth Low Energy (BLE) ATT/GATT HID All GATT-based profile supported SPP-Like GATT-based profile BLE Beacon A2DP/AVRCP/SPP, HSP/HFP, RFCOMM CVSD and SBC for audio codec Bluetooth Piconet and Scatternet LoRa Operating Frequencies 868MHz(Europe) at 14dBm maximum 915MHz (North and South America, Australia and New Zealand) at 20dBm maximum LoRa Specification Power consumption: 10mA Rx, 28mA Tx LoRaWAN stack – Class A and C devices Node range: Up to 40km Nano-gateway: Up to 12km (Capacity up to 200 nodes) Auto-connect to the ThingsNetwork WiFi Networking Up to 1km range 802.11b/g/n 16mbps Power: 12mA in active mode, 5uA in standby Size 41 x 24 x 12.5 (mm)

Cellular LTE-M (Cat NB1 and M1) multipurpose wearable device featuring Pymesh and LTE-M (Cat NB1 and M1), LoRa, WiFi and Bluetooth OLED (Piezo touch screen) GPS Accelerometer State of the art antennas LiPo battery QI wireless charging 6 exposed pins (2 charging/4 universal in/out) Meet the PyGo2 which is in essence a FiPy module on steroids! We packed the FiPy in an IP67 case, gave it an OLED (Piezo touch screen sensing), a GPS, an accelerometer, some state of the art antennas, a LiPo battery and a QI wireless charging solution. The PyGo2 features six exposed pins: 2 for power and 4 universal inputs/outputs with digital/analogue capabilities so that you can connect different types of sensors and actuators. Developers can physically connect Things and sensors to a PyGo! And yes, before you ask, rest assured, we will be adding electrical circuit protection to ensure PyGo can have a bath and still retain its cool IP67 protection. Best of all, the PyGo modules are fully programmable using existing Pycom IDE such as Pymakr and can link up with any other Pycom modules. We launched the PyGo modules with the ability to mesh together at distance of up to 12KM. PyGo2 includes WiFi, Bluetooth, LoRa, Sigfox and dual LTE-M (embedded SIM for CAT M1 and NB IoT) the PyGo2 gives access to all the world’s LPWAN networks on one tiny board. The PyGo2 includes 1-year of Sigfox connectivity. If you are purchasing the PyGo2 and wish to connect via USB to your computer, you will also need to purchase either the PyGo cradle.   PyGo2 Features Powerful CPU Five networks: WiFi, BLE, cellular LTE-CAT M1/NB1 (embedded SIM chip), LoRa (and LoRa MESH) and Sigfox Up to 1KM WiFi range MicroPython enabled Ultra-low power usage: a fraction compared to other connected microcontrollers Pymakr IDE supported Pylife Application with IFTTT style environment for light programming OLED IP67 rated Qi Wireless charging Processing Espressif ESP32 SoC Dual processor and WiFi radio system on chip Networking processor handles the WiFi connectivity and the IPv6 stack Main processor is entirely free to run the user application An extra ULP-coprocessor that can monitor GPIOs, the ADC channels and control most of the internal peripherals during deep-sleep mode while only consuming 25uA Interfaces Analog channels: 8_12 bit ADCs, 2_8 bit DAC Timers: 2_64 bit with PWM with up to 16 channels DMA on all peripherals 2 Pins (Power) GPIO: 4 analog input (0-3.3V 12bit SAR ADC) and digital (3.3V logic) input/output pins. Hash / Encryption SHA, MD5, DES, AES WiFi Networking 802.11b/b/n 16mbps Bluetooth Low energy and classic RTC Running at 32KHz Range Node range: Up to 50km Security & Certifications SSL/TLS support up to 1.2 WPA Enterprise security AES encryption engine Memory RAM: 4MB Flash Memory: 8MB Hardware floating point acceleration Python multi-threading Power LiPo battery: 420mAh LiPo 4.2V Pymesh Connect upto 200 devices in a mesh using our LoRamesh technology Sigfox Operating Frequencies RCZ1 – 868MHz(Europe) RCZ2 – 902MHz (US, Canada and Mexico) RCZ3 – (Japan and Korea) RCZ4 – 920-922MHz (ANZ, Latin America and S-E Asia) Sigfox Specification Semtech SX1272 – Long Range, Low Power RF Transceiver 860-1000MHz with LoRa® Technology Class 0 device. Maximum Tx power: – 14dBm (Europe) – 22dBm (America) – 22dBm (Australia and New Zealand) Node range: Up to 50km Sigfox pre-certified (October 2016) Power Sigfox (Europe): 17mA in Rx mode, 47mA in Tx mode and 0.5uA in standby Sigfox (Australia, New Zealand and South America): 24mA in rX mode, 257 mA in Tx mode and 0.5uA in standby Bluetooth Networking Low energy and classic Compliant with Bluetooth v4.2 BR/EDR and BLE specification Class-1, Class-2 and Class-3 transmitter without external power amplifer Enhanced power control 10dBm transmitting power NZIF receiver with -98 dBm sensitivity Adaptive Frequency Hopping (AFH) Standard HCI based on SDIO/SPI/UART High speed UART HCI, up to 4 Mbps BT 4.2 controller and host stack Service Discover Protocol (SDP) General Access Profile (GAP) Security Manage Protocol (SMP) Bluetooth Low Energy (BLE) ATT/GATT HID All GATT-based profile supported SPP-Like GATT-based profile BLE Beacon A2DP/AVRCP/SPP, HSP/HFP, RFCOMM CVSD and SBC for audio codec Bluetooth Piconet and Scatternet LoRa Operating Frequencies 868MHz(Europe) at 14dBm maximum 915MHz (North and South America, Australia and New Zealand) at 20dBm maximum LoRa Specification Power consumption: 10mA Rx, 28mA Tx LoRaWAN stack – Class A and C devices Node range: Up to 40km Nano-gateway: Up to 12km (Capacity up to 200 nodes) Auto-connect to the ThingsNetwork LTE-M Operating Frequencies 34 bands supports from 699Mhz to 2170Mhz (Total world-wide support) LTE-M Specification One single chip for both CAT M1 and NB1 (yes, only one chip) 3GPP release 13 LTE Advanced Pro Supports narrowband LTE UE categories M1/NB1 Integrated baseband, RF, RAM memory and power management Reduced Tx power class option Peak power estimations: TX current = 420mA peak @1.5Watt RX current = 330mA peak @1.2Watt – Data rates: 300 kbps DL 375 kbps UL (LTE Cat M1 in 1.4 Mhz, HD-FDD) 40 kbps DL 55 kbps UL (LTE Cat M2 in 200 kHz, HD-FDD) Tx/Rx Frequencies Ports for LTE Bands Tx frequencies Rx frequencies Low bands 5, 8, 12, 13, 18, 19, 20, 28 699 to 915 MHz 729 to 960 MHz Mid bands 1, 2, 3, 4 1710 to 1980MHz 1805 to 2170 MHz WiFi Networking Up to 1km range 802.11b/g/n 16mbps Power: 12mA in active mode, 5uA in standby Size 41 x 24 x 12.5 (mm)

Pyscan is a sensor shield you can use with any of your Pycom multi-network development boards! Featuring an accelerometer, ambient light sensor and RFID (NFC/RFID antenna included with purchase) Pyscan Features 3 axis 12-bit accelerometer Ambient light sensor RFID-NFC Chip USB port with serial access LiPo battery charger MicroSD card compatibility Ultra low power operation (~1uA in deep sleep) NFC / RFID Antenna included Use with Pybytes Crafted by a group of Pycom back-end experts, the Pybytes platform is everything there needs to be in place to gather, organise and display your data free of charge in the cloud. Regardless of whether you are a company, IoT system architect, or an ambitious tech hobbyist we?ll soon get you connected. Size 55mm x 35mm x 10mm

Imagine a sensor shield which you can use with any of your Pycom multi-network modules. This is what we give you with Pysense and Pytrack a leg up to get you off to a great start really quickly. These little fellows fit all Pycom boards and each contain a number of sensors. NOTE: WiPy is not included Pysense Features Ambient light sensor Barometric pressure sensor Humidity sensor 3 axis 12-bit accelerometer Temperature sensor USB port with serial access LiPo battery charger MicroSD card compatibility Ultra low power operation (~1uA in deep sleep) Use with Pybytes Crafted by a group of Pycom back-end experts, the Pybytes platform is everything there needs to be in place to gather, organise and display your data free of charge in the cloud. Regardless of whether you are a company, IoT system architect, or an ambitious tech hobbyist we?ll soon get you connected. Size 55mm x 35mm x 10mm

Imagine a sensor shield which you can use with any of your Pycom multi-network modules! This is what we give you with Pysense and Pytrack a leg up to get you off to a great start really quickly. Pytrack Features Super accurate GNSS Glonass GPS 3 axis 12-bit accelerometer USB port with serial access LiPo battery charger MicroSD card compatibility Ultra low power operation (~1uA in deep sleep) Location Services Supported GPS GLONASS Galileo QZSS Use with Pybytes Crafted by a group of Pycom back-end experts, the Pybytes platform will be everything there needs to be in place to gather, organise and display your data free of charge in the cloud. Regardless of whether you are a company, IoT system architect or an ambitious tech hobbyist we’ll soon have you connected. Size 55m x 35mm x 10mm

The SiPy is a multi-network (Sigfox, WiFi and BLE) development platform. It is programmable with MicroPython and the Pymakr IDE for fast IoT application development, easy programming in-field and extra resilience with network failover. The best blend of speed to deployment and access to new LPWAN networks rolling out across Europe, USA, Africa and India. You can also configure the SiPy in FSK mode to send packets directly from SiPy to SiPy. This way you can create the network configuration of your choice and then use another SiPy as central Nano-Gateway to forward the data to the cloud via WiFi. Our module is CE, FCC, IC and RCM certified! NOTE: SIGFOX CONNECTIVITY IS INCLUDED FOR 12 MONTHS FROM FIRST USE OF DEVICE FOR DEVELOPMENT UNITS. THIS DOES NOT INCLUDE LARGER DEPLOYMENTS/COMMERCIAL USE WHERE A PAYABLE SERVICE WILL BE REQUIRED. CONTACT PYCOM FOR PRICING NOTE: Using the Sigfox radio without the external antenna can lead to damage of the device and is therefore not recommended. If you are purchasing the SiPy and wish to connect via USB to your computer, you will also need to purchase either the Expansion Board 3.0, Pysense or Pytrack. SiPy Features Powerful CPU, BLE and state of the art WiFi radio1KM WiFi rangeMicroPython enabledFits in a standard breadboard (with headers)Ultra-low power usage: a fraction compared to other connected micro controllers Processing Espressif ESP32 chipset Dual processor and WiFi radio system on chip Network processor handles the WiFi connectivity and the IPv6 stack Main processor is entirely free to run the user application An extra ULP-coprocessor that can monitor GPIOs, the ADC channels and control most of the internal peripherals during deep-sleep mode while only consuming 25uA Sigfox Operating Frequencies RCZ1 – 868MHz (Europe) RCZ2 – 902MHz (US, Canada and Mexico) RCZ3 – (Japan and Korea) RCZ4 – 920-922MHz (ANZ, Latin America and S-E Asia) Interfaces 2 x UART, 2 x SPI, I2C, I2S, micro SD card Analog channels: 8_12 bit ADCs Timers: 4_16 bit with PWM and input capture DMA on all peripherals GPIO: Up to 24 Hash / Encryption SHA, MD5, DES, AES WiFi Networking 802.11b/g/n 16mbps Bluetooth Low energy and classic RTC Running at 32KHz Range Node range: Up to 50km Security & Certifications SSL/TLS support WPA Enterprise security AES encryption engine Memory RAM: 512kb Flash Memory: 4MB GPIO: Up to 24 Hardware floating point acceleration Python multi-threading Sigfox Specification TI CC1125NarrowbandTransceiver Class 0 device. Maximum Tx power: 14dBm (Europe) 22dBm (America) 22dBm (Australia and New Zealand) Node range: Up to 50km Sigfox certified Power Voltage Input: 3.3V  5.5V 3v3 output apable of sourcing up to 400mA WiFi: 12mA in active mode, 5uA in standy Sigfox (Europe): 17mA in Rx mode, 47mA in Tx mode and 0.5uA in standby Sigfox (Australia, New Zealand and South America): 24mA in Rx mode, 257 mA in Tx mode and 0.5uA in standby Size 55mm x 20mm x 3.5mm (Without Headers)

The SiPy Multipack of 1, 2 or 5 development boards that lets you add sensor shields and antennas in a bundle. With Sigfox, Wifi and BLE, the SiPy is a triple bearer MicroPython enabled micro controller that enabled flexible connectivity to Sigfox networks around the world. Here’s the five pack that enables you to get started for real on the Sigfox networks. This enterprise grade IoT platform features the powerful Espressif ESP32 chipset, the SiPy offers a perfect combination of power, friendliness and flexibility. This bundle also include the LoRa/Sigfox antenna and a sensor shield of your choice: the Expansion board, Pysense or Pytrack. Create and connect your things everywhere. Fast. SiPy Specifications Inexpensive, small and breadboard friendly Ultra low power (850uA with the WiFi connection active) 100% PYTHON PROGRAMMABLE Lots of GPIOs, interfaces and peripherals Powerful CPU, BLE and state of the art WiFi radio LoPy Size: 55mm x 20mm x 3.5mm (without headers) Hardware floating point acceleration Python multi-threading Weight: 7g NOTE: Using the Sigfox radio without the external antenna can lead to damage of the device and is therefore not recommended. Pyscan Features 3 axis 12-bit accelerometer Ambient light sensor RFID-NFC Chip USB port with serial access LiPo battery charger MicroSD card compatibility Ultra low power operation (~1uA in deep sleep) NFC / RFID Antenna included     Pytrack Features Super accurate GNSS Glonass GPS 3 axis 12-bit accelerometer USB port with serial access LiPo battery charger MicroSD ard compatibility Ultra low power operation (~1uA in deep sleep)   Pysense Features Ambient light sensor Barometric pressure sensor Humidity sensor 3 axis 12-bit accelerometer Temperature sensor USB port with serial access LiPo battery charger MicroSD card compatibility Ultra low power operation (~1uA in deep sleep)   Expansion Board Features USB and LiPo battery powered FT234XD USB to serial converter LiPo battery charger (BQ24040), with options for two different charging currents (100mA and 450mA) TPS2115A with reverse voltage protection MicroSD card slot Three female headers to easily plug in the WiPy, LoPy, SiPy, FiPy or GPy. JST style battery connector Power LED and charge status LED One user LED and one user switch Battery voltage monitoring via the WiPy ADC Lots of jumpers to enable/disable feature     LoRa/Sigfox Antenna Kit External antenna. RF Cable Assemblies RP-SMA (Female) JK-IPEX MHF U.FL 1.13 100MM RP-SMA (Male) Tilt Swivel 1/2 Wave Whip antenna Weight: 21g PLEASE NOTE: The Espressif ESP32 firmware on Pycom modules is continuously evolving and buyers are reminded that regular firmware updates will be made available. Compatible with Pymakr plugins

No drills, all thrills. The Universal IP67 Case is Pycom’s very own universal waterproof case, with push-in tabs that fit accessory sensors perfectly, creating a water tight seal. Two holes go straight through the case without penetrating the inner compartment, meaning you can fix the case securely in place. The case features perfectly sized spacing for a Pycom expansion board or sensor shield, a Pycom module and battery, plus sensors. The outer dimensions of the case are: 8.8 x 8.8 x 4cm The Universal IP67 Case has push-in tabs that specifically fit the following sensors perfectly (coming soon), as well as all of our antennas, which you can purchase separately: 2MP Camera Infrared Image Sensor Barcode Reader Fingerprint Scanner OLED Screen (11mm x 12mm screen area)

Reference Board used to mount either all Pycom OEM modules (including our cellular range eg G01). Provides the same functionality and pin-out as the developer version of the modules and can be mounted straight-out-of the box. Contains: – RGB LED – 5V to 3.3V DC-DC switching regulator -ufl connectors for the LoRa and cellular antennas – Triple antenna options for WiFi-BLE/LoRa868-915MHz/LoRa433MHz/Cellular – Male header pins – Nano Sim card slot Find support on our documentation: docs.pycom.io And community help on our forum: forum.pycom.io

The W01 is the WiPy OEM module. It works exactly like your WiPy but we’ve trimmed a few bits to make it smaller and easier to integrate. Dual network BLE and WiFi. Fits on the Pycom OEM Reference Board. Drawings and reference design The drawings can be found here. The pinout design is available here. Not included in W01 Voltage regulator Reverse power supply protection Antenna switch SMD antenna u.fl connectors Reset switch LED Headers A few passive components You will be given full technical support to design-in / integrate the module onto your product PCB. Nothing else changes and the good thing is that you’ll be able to use the same applications on your W01 and on your WiPy which makes everything a doddle. Supplied in high volume assembly format (with SMT pads). There’s no packaging to unwrap. The W01 can be supplied and used straight from a hermetically sealed reel. It’s the ideal solution for high volume deployments. it comes CE, FCC, IC and RCM certified. Whilst Pycom plans carefully to ensure modules are always in stock, in the eventuality of these being “Out-Of-Stock”, then deliveries will be circa 8-12 weeks from order receipt. Contact us on sales@pycom.io for more details W01 Features Powerful CPU, BLE and state of the art WiFi radio. 1KM Wifi Range MicroPython enabled Fits on the Pycom OEM Reference Board. Ultra-low power usage: a fraction compared to other connected micro controllers Processing Espressif ESP32 chipset Dual processor WiFi radio System on Chip Network processor handles the WiFi connectivity and the IPv6 stack Main processor is entirely free to run the user application An extra ULP-coprocessor that can monitor GPIOs, the ADC channels and control most of the internal peripherals during deep-sleep mode while only consuming 25uA Interfaces 2 x UART, 2 x SPI, I2C, I2S, micro SD card Analog channels: 8×12 bit ADCs Timers: 4×16 bit with PWM and input capture DMA on all peripherals GPIO: Up to 24 Hash / encryption SHA, MD5, DES, AES WiFi 802.11b/g/n 16mbps Bluetooth Low energy and classic RTC Running at 32KHz Power Voltage Input: 3.3V regulated Security & Certifications SSL/TLS support WPA Enterprise security FCC – 2AJMTW01XXX CE 0700 Memory RAM: 4MB Flash Memory: 8MB Hardware floating point acceleration Python multi-threading

WiPy 3.0 is Pycom’s updated enterprise grade IOT development platform. The tiny MicroPython enabled WiFi & Bluetooth IoT development platform. With a 1KM WiFi range, state of the art Espressif ESP32 chipset and dual processor, the WiPy 3.0 is all about taking the Internet of Things to the next level. We’ve written an powerful and intuitive Python API to take advantage of every feature of the hardware. The learning curve is minimal. Simply put, Pycom boards are all about Python and the internet, but with rocket fuel. If you are purchasing the WiPy 3.0 and wish to connect via USB to your computer, you will also need to purchase either the Expansion Board 2.0, Pysense or Pytrack. Features Powerful CPU, BLE and state of the art WiFi radio 1KM WiFi range MicroPython enabled, the Linux of IoT for fast deployment Fits in a standard breadboard (with headers) Ultra-low power usage: a fraction compared to other connected micro controllers Processing Espressif ESP32 chipset Dual processor WiFi radio system on chip Network processor handles the WiFi connectivity and the IPv6 stack Main processor is entirely free to run the user application An extra ULP-coprocessor that can monitor GPIOs, the ADC channels and control most of the internal peripherls during deep-sleep mode while only consuming 25uA Interfaces 2 x UART, 2 x sPI, I2C, I2S, micro SD card Analog channels: 8_12 bit ADCs Timers: 4_16 bit with PWM and input capture DMA on all peripherals GPIO: Up to 24 Hash/Encryption SHA, MD5, DES, AES WiFi 802.11b/g/n 16mbps Bluetooth Low energy and classic RTC Running at 32KHz Power 3.3V to 5.5V 3V3 output capable of sourcing up to 550mA Security & Certifications SSL/TLS support WPA Enterprise security FCC 2AJMTWIPY3R CE 0700 Memory RAM: 4MB External flash: 8MB Hardware floating point acceleration Python multi-threading Size 42mm x 20mm x 2.5mm (excluding headers)