The Argon is a powerful Wi-Fi enabled development kit that can act as either a standalone Wi-Fi endpoint or Wi-Fi enabled gateway for Particle Mesh networks. It is based on the Nordic nRF52840 and has built-in battery charging circuitry so it’s easy to connect a Li-Po and deploy your local network in minutes. The Argon is great for connecting existing projects to the Particle Device Cloud or as a gateway to connect an entire group of local endpoints. Specs Espressif ESP32-S0WD 2.4G Wi-Fi coprocessor On-board 1MB flash for ESP32 chip 802.11 b/g/n support 802.11 n (2.4 GHz), up to 150 Mbps Nordic Semiconductor nRF52840 SoC ARM Cortex-M4F 32-bit processor @ 64MHz 1MB flash, 256KB RAM IEEE 802.15.4-2006: 250 Kbps Bluetooth 5: 2 Mbps, 1 Mbps, 500 Kbps, 125 Kbps Supports DSP instructions, HW accelerated Floating Point Unit (FPU) calculations ARM TrustZone CryptoCell-310 Cryptographic and security module Up to +8 dBm TX power (down to -20 dBm in 4 dB steps) NFC-A tag On-board additional 2MB SPI flash 20 mixed signal GPIO (6 x Analog, 4 x PWM), UART, I2C, SPI Micro USB 2.0 full speed (12 Mbps) Integrated Li-Po charging and battery connector JTAG (SWD) Connector RGB status LED Reset and Mode buttons On-board 2.4GHz PCB antenna for Thread/BLE or Wi-Fi (user selectable) Two U.FL connectors for external antennas (one for Thread/BLE, another for Wi-Fi) Meets the Feather specification in dimensions and pinout FCC, CE and IC certified RoHS compliant (lead-free)

The Boron GSM is a powerful 2G/3G enabled development kit that can act as either a standalone cellular endpoint or 2G/3G enabled gateway for Particle Mesh networks. It is based on the Nordic nRF52840 and has built-in battery charging circuitry so it’s easy to connect a Li-Po and deploy your local network in minutes. The Boron is great for connecting existing projects to the Particle Device Cloud or as a gateway to connect an entire group of local endpoints where Wi-Fi is missing or unreliable. Specs u-blox SARA U201 2G/3G modem HSPA/GSMqq with global hardware and SIM support 3GPP Release 7 Bands 800/850/900/1900/2100 MHz Nordic Semiconductor nRF52840 SoC ARM Cortex-M4F 32-bit processor @ 64MHz 1MB flash, 256KB RAM IEEE 802.15.4-2006: 250 Kbps Bluetooth 5: 2 Mbps, 1 Mbps, 500 Kbps, 125 Kbps Supports DSP instructions, HW accelerated Floating Point Unit (FPU) calculations ARM TrustZone CryptoCell-310 Cryptographic and security module Up to +8 dBm TX power (down to -20 dBm in 4 dB steps) NFC-A tag On-board additional 2MB SPI flash 20 mixed signal GPIO (6 x Analog, 4 x PWM), UART, I2C, SPI Micro USB 2.0 full speed (12 Mbps) Integrated Li-Po charging and battery connector JTAG (SWD) Connector RGB status LED Reset and Mode buttons Dual SIM support: nano 4FF and MFF2 U.FL connector for external antenna Meet the Feather specification in dimensions and pinout FCC and PTCRB certified RoHS compliant (lead-free)

  The Boron LTE is a powerful LTE CAT-M1/NB1 enabled development kit that can act as either a standalone cellular endpoint or LTE enabled gateway for Particle Mesh networks. It is based on the Nordic nRF52840 and has built-in battery charging circuitry so it’s easy to connect a Li-Po and deploy your local network in minutes. The Boron is great for connecting existing projects to the Particle Device Cloud or as a gateway to connect an entire group of local endpoints where Wi-Fi is missing or unreliable. All Particle hardware is designed from the ground up to work with the Device Cloud; a powerful set of tools and infrastructure to build, connect, and manage your IoT fleet. The Device Cloud for Particle Mesh is priced by network. All Particle customers get 3 free months of Device Cloud access for micro networks using a cellular gateway. A micro network is defined as a network with 10 total devices and a single gateway. Please refer to our pricing documentation for more information. Contents: Boron LTE dev board Mini breadboard Cellular flex antenna USB cable Starter project includes two resistors (220 ohm), one red LED, and one photodiode Specs: u-blox SARA R410 LTE modem  - LTE CAT M1/ NB1 module with global hardware support (MVNO support for US only)  - 3GPP Release 13 LTE Cat M1 Nordic Semiconductor nRF52840 SoC  - ARM Cortex-M4F 32-bit processor @ 64MHz  - 1MB flash, 256KB RAM  - IEEE 802.15.4-2006: 250 Kbps  - Bluetooth 5: 2 Mbps, 1 Mbps, 500 Kbps, 125 Kbps  - Supports DSP instructions, HW accelerated Floating Point Unit (FPU) calculations  - ARM TrustZone CryptoCell-310 Cryptographic and security module  - Up to +8 dBm TX power (down to -20 dBm in 4 dB steps)  - NFC-A tag On-board additional 2MB SPI flash 20 mixed signal GPIO (6 x Analog, 8 x PWM), UART, I2C, SPI Micro USB 2.0 full speed (12 Mbps) Integrated Li-Po charging and battery connector JTAG (SWD) Connector RGB status LED Reset and Mode buttons Dual SIM support: Nano 4FF (unpopulated) and MFF2 U.FL connector for external antenna Meets the Feather specification in dimensions and pinout FCC and PTCRB certified RoHS compliant (lead-free) 

The Boron LTE is a powerful LTE CAT-M1/NB1 enabled development kit that can act as either a standalone cellular endpoint or LTE enabled gateway for Particle Mesh networks. It is based on the Nordic nRF52840 and has built-in battery charging circuitry so it’s easy to connect a Li-Po and deploy your local network in minutes. The Boron is great for connecting existing projects to the Particle Device Cloud or as a gateway to connect an entire group of local endpoints where Wi-Fi is missing or unreliable. Specs u-blox SARA R410 LTE modem LTE CAT M1/ NB1 module with global hardware support (MVNO support for US/Mexico only) 3GPP Release 13 LTE Cat M1 EGPRS Power Class E2 Nordic Semiconductor nRF52840 SoC ARM Cortex-M4F 32-bit processor @ 64MHz 1MB flash, 256KB RAM IEEE 802.15.4-2006: 250 Kbps Bluetooth 5: 2 Mbps, 1 Mbps, 500 Kbps, 125 Kbps Supports DSP instructions, HW accelerated Floating Point Unit (FPU) calculations ARM TrustZone CryptoCell-310 Cryptographic and security module Up to +8 dBm TX power (down to -20 dBm in 4 dB steps) NFC-A tag On-board additional 2MB SPI flash 20 mixed signal GPIO (6 x Analog, 4 x PWM), UART, I2C, SPI Micro USB 2.0 full speed (12 Mbps) Integrated Li-Po charging and battery connector JTAG (SWD) Connector RGB status LED Reset and Mode buttons Dual SIM support: Nano 4FF (unpopulated) and MFF2 U.FL connector for external antenna Meets the Feather specification in dimensions and pinout FCC and PTCRB certified RoHS compliant (lead-free)

This penta-band GSM antenna from industry leader Taoglas is a great multi-purpose antenna for almost all cellular applications. It's compact size makes it convenient for design into small enclosures, and it features a rigid structure that ensures minimal gain loss during integration.  This antenna attaches directly to the u.FL connector on the Electron, and is the same antenna that we include with all of our Electron development kits. RoHS compliant, and includes 3M adhesive for easy integration into enclosures. Specifications Dimensions 80 x 20.8 x 1.0 mm Cable Length 164.9mm Connector u.FL (IPEX) Gain Average -1.32 to -3.26 dBi Frequency Range 850/900/1800/1900/2100 MHz bands Input Impedance 50Ω

The E Series is Particle’s newest product family of industrialized cellular IoT modules. E Series Product Features Particle’s E Series is a new family of production-grade 2G, 3G, and LTE-enabled hardware that vastly reduces the cost and complexity of deploying cellular-connected IoT solutions at scale. All E Series modules include the following features:       - Embedded SIM card, which resists vibration, corrosion, and mechanical failure          - Surface-mountable design, for PCB assembly in mass-production        - Industrial temperature range from -20 to 85C for deployment in hostile environments        - Future-compatible pinout with support for 2G and 3G today and a seamless transition to LTE M1 and NB1 in 2018        - Fully certified design virtually eliminating the cost and complexity of RF and carrier compliance        - Built-in compatibility with Particle's development tools, messaging platform, and device management console The E310 module supports worldwide 2G and 3G connectivity and can be configured into a 2G only mode. All Particle Hardware is designed from the ground up to work with the Device Cloud. The Device Cloud is a powerful set of tools and infrastructure to build, connect, and manage your IoT fleet. Access to the Device Cloud includes: 3MB of cellular data per device/mo (additional data $0.40/MB for most countries) Device Cloud Features:  Device Management Over the Air Firmware Updates Fully Managed Connectivity Developer Tools Integrations Specs: STM32F205 ARM Cortex M3 microcontroller 1MB Flash, 128K RAM Cellular modem: u-blox SARA U-series (3G Global with 2G fallback) 36 pins total: 28 GPIOs (D0-D13, A0-A13), plus TX/RX, 2 GNDs, VIN, VBAT, WKP, 3V3, RST Board dimensions: 36mm x 43mm   

The E Series is Particle’s newest product family of industrialized cellular IoT modules. The E Series Evaluation Kit provides everything you need to build your first industrial-grade proof-of-concept on the Particle platform. E Series Product Features All E Series modules include the following features:       - Embedded SIM card, which resists vibration, corrosion, and mechanical failure          - Surface-mountable design, for PCB assembly in mass-production        - Industrial temperature range from -20 to 85C for deployment in hostile environments        - Pinout with support for LTE M1 and a seamless transition from 2G/3G (future-compatible for NB1)        - Fully certified design virtually eliminating the cost and complexity of RF and carrier compliance        - Built-in compatibility with Particle's development tools, messaging platform, and device management console The E402 module supports LTE M1 connectivity. All Particle Hardware is designed from the ground up to work with the Device Cloud. The Device Cloud is a powerful set of tools and infrastructure to build, connect, and manage your IoT fleet. Access to the Device Cloud includes: 3MB of cellular data per device/mo (additional data $0.40/MB for most countries) First 3 months of Device Cloud FREE ($2.99 per device/mo after) Device Management Over the Air Firmware Updates Fully Managed Connectivity Developer Tools Integrations Specs: STM32F205 ARM Cortex M3 microcontroller 1MB Flash, 128K RAM Cellular modem: u-blox SARA U-series (LTE M1) 36 pins total: 28 GPIOs (D0-D13, A0-A13), plus TX/RX, 2 GNDs, VIN, VBAT, WKP, 3V3, RST Board dimensions: 36mm x 43mm 

The Electron 2G Kit is a tiny development kit for creating cellular-connected electronics projects and products. It comes with a Particle SIM card with service in more than 100 countries worldwide. All Particle Hardware is designed from the ground up to work with the Device Cloud. The Device Cloud is a powerful set of tools and infrastructure to build, connect, and manage your IoT fleet. Access to the Device Cloud includes: 3MB of cellular data per device/mo (additional data $0.40/MB for most countries) First 3 months of Device Cloud FREE ($2.99 per device/mo after) Device Cloud Features:  - Device Management  - Over the Air Firmware Updates  - Fully Managed Connectivity  - Developer Tools  - Integrations Contents: Particle Electron PCB Particle SIM Card Li-Po battery (2000mAh) Taoglas Cellular Antenna USB cable Breadboard Pinout reference card Components for a sample product Specs: STM32F205 ARM Cortex M3 microcontroller 1MB Flash, 128K RAM Cellular modem: u-blox SARA G-series (2G) 36 pins total: 28 GPIOs (D0-D13, A0-A13), plus TX/RX, 2 GNDs, VIN, VBAT, WKP, 3V3, RST Board dimensions: 2.0" x 0.8" x 0.3" (0.5" including headers) Country compatibility*: North America (limited timeline) South America Europe Asia Oceania 2G coverage will now exist in the United States until 2020 through T-Mobile.  Please note that the Electron is a GSM-only device, and does not support CDMA networks. Many global carriers are planning to sunset their 2G networks beginning as soon as late 2016 and early 2017, so please confirm continued 2G service with your local carrier. We recommend 3G Electrons for anyone concerned about long-term cellular support in their home country. 2G Electrons will not work in Japan, where 2G networks have already been discontinued.   

The Electron 3G Kit is a tiny development kit for creating 3G cellular-connected electronics projects and products. It comes with a Particle SIM card with service in more than 100 countries worldwide. All Particle Hardware is designed from the ground up to work with the Device Cloud. The Device Cloud is a powerful set of tools and infrastructure to build, connect, and manage your IoT fleet. Access to the Device Cloud includes:   3MB of cellular data per device/mo (additional data $0.40/MB for most countries) First 3 months of Device Cloud FREE ($2.99 per device/mo after) Device Cloud Features:- Device Management- Over the Air Firmware Updates- Fully Managed Connectivity- Developer Tools- Integrations Contents Particle Electron PCB Particle SIM Card Li-Po battery Taoglas Cellular Antenna USB cable Breadboard Pinout reference card Components for a sample product Specs STM32F205 ARM Cortex M3 microcontroller 1MB Flash, 128K RAM Cellular modem: u-blox SARA U-series (3G) 36 pins total: 28 GPIOs (D0-D13, A0-A13), plus TX/RX, 2 GNDs, VIN, VBAT, WKP, 3V3, RST Board dimensions: 2.0" x 0.8" x 0.3" (0.5" including headers)  

This book teaches you how to begin with the Particle development tools, deploy your sketches over WiFi, and build electronic projects that take advantage of the Photon's processing power, cloud platform, and input/output pins. Filled with projects, examples and tips, Getting Started with the Photon is useful whether you're new to electronics or an advanced user looking to get started with Particle. Chapters Include: Quick Start Programming the Photon If This Then That Machine to Machine Communication and more... Written by Dr. Simon Monk, the author of '15 Dangerously Mad Projects for the Evil Genius' and 'Arduino + Android Projects for the Evil Genius'.

Please note the Grove Starter Kit does not include a Particle development board. You will need to purchase a Particle Mesh Argon or Boron to accompany this kit. The Starter Kit is designed to make your first exploration into the world of sensing and actuating a breeze. The kit comes with seven different components that work out-of-the-box with Particle Mesh hardware and let you focus on learning the basics. Working with Starter Kit requires no soldering and minimal wiring. Simply connect the kit’s Grove Shield (the new co-developed FeatherWing adapter from Particle and Grove) to your Particle Mesh board and use the included cables to connect the adapter and the sensors and actuators that you want to use. It’s a plug-and-play experience. Features 1.  Grove Shield for Particle Mesh - Plug and play your Particle Mesh Argon or Boron in the FeatherWing form factor; includes Grove connectors (3 Digital, 2 analog, 2 I2C_1, 1 UART) 2.  Button - A momentary push button that uses Standard 4-pin Grove Cables to connect to other Grove modules 3.  Rotary Angle Sensor - Also known as a ‘potentiometer’, this sensor produces analog output between 0 and Vcc 4.  Ultrasonic Ranger - A non-contact distance measurement module working at 40KHz 5.  Temp&Humi Sensor - Highly reliable and integrated temperature and humidity sensor 6.  Light Sensor v1.2 - Integrates a photo-resistor to detect light intensity and can be used to build a light controlled switch 7.  Chainable RGB LED - Full-color LED driver with 3 constant-current drivers as well as modulated output of 256 shades of gray 8.  Buzzer - Easy to use piezoelectric buzzer with a sound output of >85dB 9.  4-Digit Display - Red alpha-numeric display with 8 adjustable luminance levels  This kit includes: 1x Grove Shield for Particle Mesh 1x Button 1x Rotary Angle Sensor 1x Ultrasonic Ranger 1x Temp&Humi Sensor 1x Light Sensor v1.2 1x Chainable RGB LED 1x Buzzer 1x 4-Digit Display

The Internet Button includes a Photon, which can also be easily removed and used for other projects, a USB-micro cable and a removable plastic cover. Quickly start playing with LEDs, multiple buttons, an accelerometer and more without any wires or soldering. On the firmware side, custom libraries are available to make programming your projects quick and beautiful. The Internet Button is not only an easy way to get started on the Internet of Things, it's also a clean and simple way to start building your own prototypes. All Particle Hardware is designed from the ground up to work with the Device Cloud. The Device Cloud is a powerful set of tools and infrastructure to build, connect, and manage your IoT fleet. Access to the Device Cloud includes: Device Cloud FREE for first 100 devices (learn more) Device Cloud Features: 1.  Device Management 2.  Over the Air Firmware Updates 3.  Fully Managed Connectivity 4.  Developer Tools 5.  Integrations Specs: 11 individually controllable RGB LEDs ADXL362 3-axis accelerometer 4 tactile buttons for D-pad style interactions Female socket for connection to Photon Additional female headers for adding extra actuators and sensors Backward compatible with the Core

The P0 is the connected brain of the Photon — a powerful, reprogrammable Wi-Fi module. Based on Cypress's BCM43362 wireless chipset, the P0 is designed to help you seamlessly transition from your Photon-powered prototype to mass production. Each module comes pre-loaded with Particle firmware. All Particle Hardware is designed from the ground up to work with the Device Cloud. The Device Cloud is a powerful set of tools and infrastructure to build, connect, and manage your IoT fleet. Access to the Device Cloud includes: Device Cloud FREE for first 100 devices (learn more) Device Cloud Features:  - Device Management  - Over the Air Firmware Updates  - Fully Managed Connectivity  - Developer Tools  - Integrations Wi-Fi Specs: Single band 2.4GHz IEEE 802.11b/g/n Supports wireless data rates of up to 65Mbit/s Ultra low power sleep, stand-by and stop modes Supports Open, WEP, WAPI, WPA and WPA2-PSK WiFi security modes Microcontroller specs: STM32F205 1MB flash, 128KB RAM 120Mhz CPU Shipping in multiples of 10 in cut tape packaging.

Thinking of transitioning from your Photon-powered prototype into mass production? The P1 is your answer. It's Particle's tiny Wi-Fi module that contains both the Cypress Wi-Fi chip and a reprogrammable STM32 32-bit ARM Cortex-M3 microcontroller. The P1 comes pre-loaded with Particle firmware. The P1 has a built-in antenna and a uFL connector, so you don't have to stress over the optimization of RF designs. This module is FCC-certified, and has additional external flash to accommodate super-hardcore projects. All Particle Hardware is designed from the ground up to work with the Device Cloud. The Device Cloud is a powerful set of tools and infrastructure to build, connect, and manage your IoT fleet. Access to the Device Cloud includes: Device Cloud FREE for first 100 devices (learn more) Device Cloud Features:  - Device Management  - Over the Air Firmware Updates  - Fully Managed Connectivity  - Developer Tools  - Integrations specs: Single band 2.4GHz IEEE 802.11b/g/n Supports wireless data rates of up to 65Mbit/s Ultra low power sleep, stand-by and stop modes Supports Open, WEP, WAPI, WPA and WPA2-PSK WiFi security modes Microcontroller Specs: STM32F205 120Mhz ARM Cortex M3 1MB flash, 128KB RAM Shipping in multiples of 10 in cut tape packaging. P1 module dimensions are: 0.787"(28mm) (W) x 1.102"(20mm) (L) x 0.0787"(2.0mm) (H) +/-0.0039"(0.1mm) (includes metal shielding).

The Particle Classic Accessory Adapter lets you use your Asset Tracker, Relay Shield, or third party shields with our third generation dev kits. Plug your Argon, Boron, or Xenon into this adapter and continue development as usual! Note: this product is a one-way adapter. That is, this product does not enable use of Adafruit FeatherWings with the Photon or Electron.

The Particle Debugger gives you the power of professional debugging at a fraction of the cost. Using this accessory, you’ll be able to program Particle mesh-ready hardware over common interfaces like JTAG and SWD, using open source tools like GDB. Supports the open source CMSIS-DAP specification and DAPLink firmware developed by ARM. Comes with one JTAG ribbon cable.

The Ethernet FeatherWing is the fastest way to add wired connectivity to your Argon, Boron, or Xenon and turns any Particle Mesh developer kit into an Ethernet gateway. Based on the WIZnet W5500 chip, this side-by-side FeatherWing maintains great RF performance even while adding Ethernet connectivity to any Particle Mesh device.

If you're new to the world of hardware, don't panic—the Maker Kit has everything you need to level up from hacker zero to hardware hero.  In addition to a shiny new Photon, the Particle Maker Kit includes all the components and accessories you need to start building simple Internet-enabled projects. The Maker Kit comes with enough jumper wires, LEDs, resistors and more to make sure you can can build multiple different types of projects. It also comes with a super-neat project carrying case so you can put tidy up your workspace when you're done building. All Particle Hardware is designed from the ground up to work with the Device Cloud. The Device Cloud is a powerful set of tools and infrastructure to build, connect, and manage your IoT fleet. Access to the Device Cloud includes: Device Cloud FREE for first 100 devices (learn more) Device Cloud Features: 1.  Device Management 2.  Over the Air Firmware Updates 3.  Fully Managed Connectivity 4.  Developer Tools 5.  Integrations What's included with the Particle Maker Kit: Photon with Headers (1) USB Micro B Cable (1) Flex antenna (1) Mini Breadboard (1) Proto-board (1) Deluxe Jumper Wire Pack (1) Male to Female Jumper Wires (10) Battery holder - 4xAA (1) Headers (7) Ceramic Capacitors (10 each) Electrolytic Capacitor 100uF (5) LEDs (10) RGB LED (1) Diode (6) IR LED (1) Resistors (30) Photoresistors (2) 10K Rotary Potentiometer (1) Temperature Sensor (1) Temperature Sensor - Sealed (1) Piezo Buzzer (1) Mini Pushbuttons (3) SPDT Switch (2) SPDT Relay (1) NPN Transistor (1) PIR sensor (1) Pancake Vibration Motor (1) Micro Servo (1) Serial OLED Screen,0.96"(1)

The Photon Kit includes a Photon with headers, a shiny white mini-breadboard, a USB-micro cable, and a couple of extra surprises to help you start building right away. All Particle Hardware is designed from the ground up to work with the Device Cloud. The Device Cloud is a powerful set of tools and infrastructure to build, connect, and manage your IoT fleet. Access to the Device Cloud includes: Device Cloud FREE for first 100 devices Device Cloud Features: 1.  Device Management 2.  Over the Air Firmware Updates 3.  Fully Managed Connectivity 4.  Developer Tools 5.  Integrations Specs: Single band 2.4GHz IEEE 802.11b/g/n Supports wireless data rates of up to 65Mbit/s Supports Open, WEP, WAPI, WPA and WPA2-PSK Wi-Fi security modes Supports Wi-Fi channels 1 to 14 Low power sleep, stand-by and stop modes

The Power Shield is the best way to—you guessed it—provide power to your mobile Particle projects. Based around the MCP73871 battery management controller, this shield allows you to simultaneously power a Photon and charge a connected Li-Ion or Li-Po battery. You'll also be able to monitor battery levels using the Photon itself, which makes the Power Shield the best way to untether your wireless project. Besides the on-board USB port, you can also use an external DC power supply or solar-cell to charge the battery. This shield ships with a 3.7V, 400mAh Li-Po battery and headers.  Designed for use with the Photon, backwards compatible with the Core. Specs: Operating voltage: USB or External DC of 7 to 20V Current consumption: 500mA max (USB) & 1.2A max (other DC sources) Dimensions: 1" x 1.84"

The new and improved Programmer Shield is essentially a USB-JTAG converter that gives advanced users complete access to the Photon's memory space. It supports openOCD and the WICED SDK, and is built around the FT2232H high speed USB FIFO. Unlike the previous Programmer Shield, it is fully standalone and requires no third-party programmers. In addition to providing a JTAG interface, this shield can also act as a USB to Serial converter. You can also use this shield as a generic JTAG programmer for your other projects! Designed for use with the Photon, backwards compatible with the Core. Specs: Operating supply: USB Current consumption: Dimensions: 1.55" x 3.3" Compatibility: OpenOCD and WICED IDE

The Relay Shield allows you to control any normal outlet or high voltage product from anywhere. The shield comes with four relays that are rated at a max of 220V @10Amp allowing you to control any electric appliance rated at under 2000 Watts. Note that you *will* need a DC adapter to power the relays! We recommend this one. Specs: Operating voltage: 7 to 15V DC Current consumption: 150mA min to 290mA (at 9V DC) Relay Max Voltage: 250V AC Relay Max Current: 10Amp at 125V AC Compatible with both the Core and the Photon.

Quantify the world! The Sensor Kit is a curated mix of awesome sensors and electrical components specifically selected by the engineers on the Particle Team. If you want to measure temperature, sense loudness, measure distances, capture motion, or detect noxious gases, the Sensor Kit has you covered. Whether you’re building a connected robot or measuring the world around you, the Sensor Kit is the place to start.  All Particle Hardware is designed from the ground up to work with the Device Cloud. The Device Cloud is a powerful set of tools and infrastructure to build, connect, and manage your IoT fleet. Access to the Device Cloud includes: 3MB of cellular data per device/mo (additional data $0.40/MB for most countries) First 3 months of Device Cloud FREE ($2.99 per device/mo after) Device Cloud Features:  - Device Management  - Over the Air Firmware Updates  - Fully Managed Connectivity  - Developer Tools  - Integrations Contents: 10 sensors for measuring acceleration, distance, temperature, humidity, motion, vibration, and gases Particle Electron PCB Particle SIM Card Li-Po battery (2000mAh) Taoglas Cellular Antenna USB cable Breadboard Pinout reference card Components for a sample product Specs: STM32F205 ARM Cortex M3 microcontroller 1MB Flash, 128K RAM Cellular modem: u-blox SARA G-series (2G) or U-series (3G) 36 pins total: 28 GPIOs (D0-D13, A0-A13), plus TX/RX, 2 GNDs, VIN, VBAT, WKP, 3V3, RST Board dimensions: 2.0" x 0.8" x 0.3" (0.5" including headers) The Sensor Kit comes with a Particle SIM card with service in more than 100 countries worldwide. The Electron is a GSM-only device, and does not support CDMA networks. We offer two types of Electron 3G Kits—one for Americas/Australia (850/1900 MHz) and one for Europe/Asia/Africa (900/1800 MHz). Check the full list of compatible countries for the location in which your product will be deployed.

The Shield Shield converts the footprint and pins of your Photon or Core into that of an Arduino, allowing for use of existing Arduino shields and accessories. This shield converts the pin mapping of the Core to the Arduino pin layout and provides a voltage translation of 3.3V to/from 5V. Compatible with both the Core and the Photon. Specs: Operating voltage: 7 to 15V DC Current consumption: standalone 7mA at 9V DC Voltage translator with auto direction detect: TXB0108PWR Dedicated MOSFET based voltage translator on I2C lines Separate unidirectional quad buffer for driving heavy loads: 74ACT125 Diode protection on ADC pins Dimensions: 3.4" x 2.1"

Add your hardware to the Particle Cloud! We sell SIM cards to add whatever cellular connected products you are creating to our easy and cheap Particle data plan. SIMs come with automatic access to the Particle Cloud platform.  The tools that make up the Photon's ecosystem (and come along with the SIM cards) are designed to let you build, create and manage your fleet of devices. You'll be able to write your firmware in our web or local IDE, deploy it over the air, and build your web and mobile apps with ParticleJS and our Mobile SDKs. Once you deploy a product, you'll be able to bulk over the air update, collect data and manage the devices in our Console. 

These external antennas are the perfect way to extend the wireless range of your Particle-powered Wi-Fi project. The ultra portable Flex Antenna is particularly useful when space is at a premium, but you want a little more range than a chip or trace antenna can provide. It requires no additional connector — it attaches directly to the u.FL connector already on your Core u.FL or Photon. Cable length - 100mm; Input Connector - IPEX(u.FL) The Duck Antenna is especially great for projects that need a metallic enclosure, which often block Wi-Fi transmission. The antenna includes an interface cable for RP-SMA to u.FL. The Duck Antenna can be used with the Photon as well as Cores with u.FL connectors. Cable length - 109mm; Input Connector - RP-SMA Specs for both antennas: Gain - 2 DBI  Frequency range 2400~2500MHz  Input Impedance - 50 Ω

The Xenon is a low cost mesh-enabled development kit that can act as either an endpoint or repeater within a Particle Mesh network. Xenon is mesh only and designed to function as the endpoint of your IoT network. It is based on the Nordic nRF52840 and has built-in battery charging circuitry so it’s easy to connect a Li-Po and deploy your local network in minutes. The Xenon is best for connecting sensors, motors, pumps, valves, and points of data-interest. Pair it with an Argon or Boron gateway to get all that great data into the Device Cloud. Specs Nordic Semiconductor nRF52840 SoC ARM Cortex-M4F 32-bit processor @ 64MHz 1MB flash, 256KB RAM IEEE 802.15.4-2006: 250 Kbps Bluetooth 5: 2 Mbps, 1 Mbps, 500 Kbps, 125 Kbps Supports DSP instructions, HW accelerated Floating Point Unit (FPU) calculations ARM TrustZone CryptoCell-310 Cryptographic and security module Up to +8 dBm TX power (down to -20 dBm in 4 dB steps) NFC-A tag On-board additional 2MB SPI flash 20 mixed signal GPIO (6 x Analog, 4 x PWM), UART, I2C, SPI Micro USB 2.0 full speed (12 Mbps) Integrated Li-Po charging and battery connector JTAG (SWD) Connector RGB status LED Reset and Mode buttons On-board PCB antenna U.FL connector for external antenna Meet the Feather specification in dimensions and pinout FCC, CE and IC certified RoHS compliant (lead-free)