Autopilot HAT for Raspberry Pi powered by ArduPilot and ROS — Navio2 — Connector for RPi — 4x spacers — 8x M2.5 screws Turn your Raspberry Pi® into a drone controller GNSS receiverTracks GPS, GLONASS, Beidou, Galileo and SBAS satellites. External antenna with MCX connector. Extention portsExposed ADC, I2C and UART interfaces for sensors and radios. High resolution barometerSenses altitude with 10 cm resolution. Dual IMUAccelerometers, gyroscopes and magnetometers for orientation and motion sensing. Triple redundant power supplyWith overvoltage protection and power module port for voltage and current sensing. RC I/O co-compressorAccepts PPM/SBUS input and provides 14 PWM output channels for motors and servos. Preconfigured OS image This is a Raspbian with ArduPilot and ROS preinstalled and ready to run with a couple of simple commands. Also comes with DroneKit and GStreamer. Program missions Use ROS or DroneKit to make your drone perform preprogrammed actions and respond to changing conditions. Stream video Transfer low-latency video from Raspberry Pi camera module to the ground control station using GStreamer. Control over the Internet Plug in 3G/LTE modem to connect to your drone from anywhere in the world and access video and telemetry data. Specifications Mechanical Size:55 x 65 mm Operating tº:-40…+85ºC Electrical Supply voltage:4.75-5.25V Power supply:Power module, servo rail, USB Average current consumption:<150mA Ports Power module UART I2C ADC 12 PWM servo outputs PPM/S.Bus input ICs MPU9250 9DOF IMU LSM9DS1 9DOF IMU MS5611 barometer U-blox M8N GLONASS/GPS/Beidou (antenna connector type MCX) Cortex-M3 RC I/O co-processor RGB LED
Navio2 GPS/GNSS Antenna MCX
This antenna is not compatible with NEO6-T USB dongle. Antenna type: active (LNA built-in) Supported navigation satellite systems: GPS, GLONASS Dimensions: 45 x 35 x 15 mm Cable length: 300 mm Connector type: MCX Mounting: adhesive Benefits Superior multipath signal rejection Great out-of-band signal rejection Excellent signal-to-noise ratio Consistent response in all op. temperatures
Power Module For Navio2
Supports LiPo batteries up to 6S Max current sensing: 60 A* Switching regulator output: 5.3 V 2.25 A 6-pos DF13 cable for connection to Navio2 power port *power module can sense current up to 90A if different connectors are used (XT60 connectors allow for 60 A max)
RTK GNSS receiver with an app as a controller Centimeter accuracy for surveying, mapping and data collection. GNSS GPS, GLONASS, BeiDou, Galileo, QZSS and SBAS Long range radio LoRa 868/915 MHz, range up to 8 km 30 hours battery life LiFePO4 battery, 5-40V input USB charging Wi-Fi and Bluetooth To connect to your device Package includes: — Reach RS+ — Carry case with a strap — Radio antenna — Adapter for survey pole — USB cable ReachView app Reach RS+ comes with a cross-platform app. It is hosted on Reach itself and accessed via Wi-Fi connection on any smartphone, tablet or laptop. For the best experience get it’s mobile version for iOS or Android. Collect points With Reach RS+ and ReachView you can create survey projects to manage data collection. When working in the field each point is assigned a custom name and offset. Results can be downloaded from the project list. 1 cm 8 GB Precision Storage File formats: DXF, GeoJSON, ESRI Shapefile and CSV. Use Reach RS+ as a base station Use Reach RS+ to set up your own base station. Stream corrections over the network via NTRIP/TCP or LoRa radio. Record base logs for post-processing. 868/915 MHz Up to 8 km LoRa radio Reliable corrections File formats: RTCM3, RINEX. Receive corrections data over the Internet You won’t always need to set up your own base station. Standalone Reach RS+ can receive corrections data over the Internet from your local NTRIP provider. No special devices or software are required, all you need is a smartphone. File formats: RTCM3, RINEX. VRS supported. Machinery guidance Reach RS+ is able to provide precise coordinates over Bluetooth/Wi-Fi to your tablet with a lightbar navigation app. RS232 interface allows to connect Reach RS directly to an autosteer system. File formats: NMEA, ERB, plain text Compatible apps: MachineryGuide, AgriBus-Navi, Efarmer Reach RS+ and ReachView are fully featured ReachView app and all features are already included in price. No extra charges or subscriptions. ReachView constantly improves and updates Simply tap the update button to receive new features and advancements. It’s always free. Protected from water, dust and falling And it floats, so you don’t have to worry you might lose it in a middle of a lake -20?…+65? IP67 -4F…149F Water- and dustproof 690 g 145 x 145 x 85 mm 1,52 lbs 5,7 x 5,7 x 3,3 inches
Tallysman Multi-GNSS Antenna
Tallysman TW4721 is a compact, wideband Accutenna™ technology GNSS antenna that provides accurate reception for all upper L- band GPS, GLONASS, Beidou, and Galileo signals (L1, G1, B1, B1 BOC, B12, E1) and associated augmentation signals (WAAS, EGNOS and MSAS SBAS). Benefits Superior multipath signal rejection Great out-of-band signal rejection Excellent signal-to-noise ratio Consistent response in all op. temperatures Specification Mechanical Architecture: Dual, quadrature feeds Size: 38 x 38 x 14 mm Attachment Method: Adhesive Electrical LNA Gain: 26 dB min Supply Current: 10 mA typ. 15 mA max. Supply Voltage: 1.8 to 16 VDC nominal Noise: 1 dB typ.